How to store structure data to eeprome and read back

hello , i want to transmit the data and recieve it on the same stm32 board using spi ,can you guide me with it

I'm working with Stm32f407VET6 Black Board and it's not working for me fresult = f_mount(&fs, "", 1); in mount_sd () gives me FR_NOT_READY . i hope you can help me

how many ohms for potentiometer ?

Great video series! Are the source files from the videos available for Download?

SIr i was trying to code this without MX on that without the External Interrupt i can get output on debugging in keil.....but with the external Interrupt i cant get output in STM STUDIO and LED is not toggled I checked the code properly it was all set....Please assist me to solve this problem!

Cool, I have the MCU stm32f030k6t6, the configuration in stm32cubemx is a little different, can you help!?😊❤

Facing an error while loading 'no target detected' Any solution please?

HI, can you help me in this code. I have tried it many time but it is not working with proteus, NEED halp.

THANKS MEN!!!!!!!!!!!!!!!!!!!!!1

thanks this series has been really helpful! do you have any idea how to 'watch' variables in the new version?

you are the best at all. pleASE SHOW US HOW TO DID MY OWN MP3 PLAYER. type by step

Is this coding / programming new old etc thx 😂just heard about it

Thanks for the effort ! Great content

Hello i try your code on STM32H7A3 but its not working, there is no printf or something to display the gyro and accerolmeter data x y z etc.

I want that code

Thanks for your video How can I get udp and tcp videos?

10:51 is 0xF in bin not 1000? And then shifted that by 12 to right is for Pin PD15? Not for Pin 12? Or what mean FUL?

Hey, if you dont mind, id have a question concerning this topic. Currently i am working on a project using stm32 and an ADS131 ADC (TexasInst). After developing and designing a pcb for this project i have to code the communication between ADC and MCU. I have basic C knowledge and very very basic (barely no xd) knowledge in programming MCUs. if you generate code from cubeMX, many files (main.c, stmxy.c, main.h, etc.) are created. It is pretty hard for me to see through this. I have some specific expectations for the communication (e.g. 10Hz, i want a timestamp (if possible?)). So, maybe you have any suggestions or help for me to get the software done.

hello sir. Thank you for sharing the video .I am a beginner and ever since I installed the IDE I have had an error message pop-up every time I open it An internal error occurred during: "AutoRegisterSchemeHandlersJob". Could not initialize class com.sun.jna.Native As well as An internal error occurred during: "Initializing External-tools". Could not initialize class com.sun.jna.Native What should do to resolve the issue?

thanks for this vodeo, it helped me a lot

Hi, great video! Can I ask you if it would be possible to use the same trigger pin for 2 transducers?

I spent last 10 hrs with the code with the same microcontroller and like all the others who commented, i got the same error because the author forgot to upload proper code.

Hi, Nice work. Could you create some videos demonstrating low-power modes, especially stop mode and standby mode, and how to analyze them using a power analyzer such as OTII?

Open source!

hi sir- mutex embedded, i'm started to learn more concept based stuffs from you.thank you so much for doing this..💯🙏..Am here coz,, i'm lesser than a yr experience embedded engineer,.as my 1st project itself involved in medical field for multi-parameter patient monitor(ecg,spo2,nibp,temp)..so.,i need to develop as already existing one in very cost effective way where things just enough to work upto its needs,.don't wanna overperformance chips or overmemories used... as i need to know, 1.which cortex architecture is suitable for 12-lead ecg data aquisition from ecg module to chip and chip to display 10.1 inch tft 1080x720 resolution..(as of now,,i 'm testing using for prototype in stm32f769i-disc0 ). 2.which type of display is easy for doing testing for external display of lvds or mipi dsi or || el 3. what will be suffient memory for handle graphic..where if external memory can be used incase of need additional.. 4.is that chip selection is based on software.,then for basic doing in patient monitor should be used linux or freertos or touchgfx or yocto linux..for using yocto linux they are using high level dual core a9 or imx6 processsor used..is there nxp's chip used in patient monitor can be replaced for stm32dual core a7+m4 of 800mhz..

Thanks for sharing this video to us!

Good afternoon! Thank you for your video and tutorials.

Please do same for SSD1963

1st doubt: InADC single conversion, we checked Poll For Conversion and once its satisfied, we get value from ADC , why we didn't check in continuous conversion mode? 2nd doubt: why we didn't give End of Conversion here?

I have been following your videos from first and I have 2 doubts in this tutorial,

mohamed where is the code why why !!

Great tutorial. How can i implement CRC to this

Very much satisfied with this tutorial after searching so many videos bro. Great work of helping lot of engineers..

Is it possible to print images stored on the board memory onto this kind of LCD?

Can this be applied to stm32G0B1CE microcontroller?

thanks. very helpful. That's all I need for my project

Actually , I have a problem , probably you can help me with , I m trying to read wav files as you did with the usb storage , this time I m trying to do it with sd card module that works with spi , the code works fine ...it reads the wav file ...but ...I hear nothing...

Don't understand why but got an error on Line 60 of .h MODE_ANALOG (expected identifier) and the same error on line 22 of.c #include "MY_CS43L22.h" (error in include chain... expected identifier). Do you know why and how to fix it?

thanks

After getting adc values (0 to 255), how to print that value in uart ?

I appreciate with heart content

Thank you so much for sharing this video. I am a beginner and now learning STM32. I have a question "Do I need to install CubeMx IDE and System WorkBench for doing a project?" My project is an oscilloscope using an STM32 Discovery kit.

In your case its legit cast to a byte, cuz u have no offset in struct and there is nothing to align and padding for compiler mem optimization.

Great job

gcc -E database.c .............run this command and see the result

sir we have no API of stm32cube framework in manage run time environment, is there any solution??

Thank you King 🙏

@Mutex_Embedded I want to interface EMMC with STM32H743VIT6 microcontroller. Could you please help me out .

I am getting "target is not responding, retrying " i am using stm32cubeide and my board is stm32l152c