Do you mean the screw @04:32? You could use a long screwdriver, preferably with magnetic tip; may need to insert through the gap between the two copper tubes, or the space around them. Hope it helps.
Do you mean the one at @04:32? Try using a screwdriver with long handle, and with magnetic tip, preferably. You may want to refer to this follow-up video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3feOelM5cXM.html
What the video doesn't show you toward the end is that you really can't lift the unit up to access the hole or clean the unit because the copper lines will get twisted. They don't show the opposite side. Why have us remove the screws to lift the condenser and see the drain hole? What we did, is access the drain hole from the back, once the exterior drain line is exposed. We cleaned the drain line out and the drain hole going in. I was hoping we didn't damage the copper lines as this video didn't show you could possible damage them if you attempt to lift the unit.
I want to see house of the dead played with this I have seen a few on Amazon with better design I just want to print of a good looking mount and blast zombies
he said pci power cable but really its a sata cable so take your sata cable and put it in your power supply then connect it with the rgb controller power cable then plug the 3 pin connecter in jrainbow 1 or jrainbow 2
I guess it is because the left end does not sit properly back in, or there may be some slight mis-alignment around there (e.g. axle holder/support at the left) and the things do not click; you may want to double check. Hope it helps.
Thanks TC. The video was very helpful. I'd have never gotten the thing open without watching your video. I was just a little frustrated with time pressure.
Thanks for watching the video! Your comment is well taken :) I just made a 2x fast-forward and muted version. Hope it helps. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-zt7yTIrHeOs.html
Not really, but you don’t need to do that. get a mini split cleaning kit from Amazon sized for your unit. It slips over the housing easily. You can remove the air vane as shown in this video. With a flashlight you should be able to aim it upward and see the blower wheel for inspection. If it’s dirty, get a can of AC coil spray cleaner at Lowes, etc. Spray it on the wheel, and let it soak for 15 minutes or so. You may need to manually rotate the blower wheel with a non-metallic tool to apply the spray to the entire wheel. After it soaks for a while, you can rinse off the blower wheel with a pump up bug/fertilizer spray bottle filled with water. Inspect for cleanliness and repeat if necessary. You will be amazed how much gook will come from the wheel. It’s worth noting, that if you lift the left end of the evaporator coil as shown in this video too far or too much, it’s possible to crack a soldered fitting on the pressurized refrigerant tubes. This will render the unit junk and require replacement of the coil, which is a very expensive service call. My guess is the unit shown in this video doesn’t get sufficient airflow because it’s too close to the ceiling and the efficiency isn’t optimal. There should be at least a foot of open space above the unit. Sometimes they have to be installed that way, but it should be avoided.
Sans aucun doute la meilleur video ;) pas de perte de temps en bavardage inutile...les détailles sont claire et precis le tous en images marquer, remarquer ;) Merci beaucoup pour vos précisions, votre travail, amitié de france
I unclogged and drained my air con but the thing is it keeps leaking 20 to 30mins after it’s been drained only to take it apart and find out it’s full again any ideas??
@@JesseVlogs the price is bad but the card basically would run most game fine at 1080p with adjusted setting plus market in different country and a lot different too and people still trusted Nvidia more that why people didn't go with 6600 instead plus Nvidia still better for E-sport game than amd gpu due to latency build in for those game.
@@flexzii6772 its not just the price you can get better cards for the same price or even lower like all the 10 series cards are far better value and performance then the 3050 it just shows its just not worth getting at all
Thank you for watching the videos. Hope it helps. Please subscribe, like and share. There will be further videos sharing my experience in installing Windows 11 in the computer. Stay tuned.
That is 100% not all the way plugged in. I can tell by the fact that the connection for the 6 by 2 arent lined up, plus the latch itself is still raised and its not pushed all the way in. I think you might wanna double check that.
Sorry to nitpick but the powerconnector that you called "pcie" is a SATA power connector. Pcie would refer to the 6+2 pin connector that plugs into a gpu.