just rubs and rubs.. tire keeps rubbing yuck

Hello there, My 2007 Camry has 4 striped head bolts. What do you think about rethread them?

6shooter arms on a 4stuck knuckle is wild to me lol.

Curious why turn the hub down

Any Engine or Drivetrain swaps/mods?

Have to tap as far as you can leave about 1/4 stickout. Clean out 3x Carefully tighten the jog as it flexes and can go out of center even with centering pin.

Looks sliiiiiick!!! Send me some pointers on converting 1980 rear drums to disc. Thanks

I have a 2007 Camry that I picked up for nothing as a non runner, blown head gasket, compression was getting into the cooling system. It had the pistons changed in 2016 by Toyota. When I removed the head bolts, several of them were very lose, but the threads didn't pull out and they seem to be in tact. The deck on the block seems to be fine after checking it with a straight edge and feeler gauge, the head is warped approximately .006, and will need to be resurfaced. I'm debating whether or not to invest in repairing the engine. The last thing I would want is to put in back together and have the head bolts pull out. I'm considering buying this kit.

the perfect 3rd gen <3

Hi, what brand and size are the front leaf springs? thanks

Good looking truck and set up, It's just not my thing to do all that crawling and do damage, but to each his own.

Not a pickup disc its called a reluctor ring. Its not a tri-square, its a double hex (very different). Thanks though

Thanks for the video. Has anyone used this kit after buying used instead of a new set? Should i repair all 10 bolts threads with this kit on my Camry or just the ones that are broken? I just have one broken threads so far. Thanks.

Do you run any bump stops on the front ?

What’s the part number on those rear studs that are longer?

How long did it take to do this repair?

How is that 4Runner so wide ? I know it has the BTF kit which is +4.5 over but 4Runner is wider !!

Hey dude how in the blue you got your tires to look so wide out? I have a 4th gen and would love to see my baby like that.

I'm going through this process right now. I get the impression that you're sliding the whole IFS hub on, does that mean you're skipping out on the snap ring for the birf? Is the outer snap ring necessary?

Awesome 4Runner! I got a 3rd Gen as well ! Makes me wanna go out there, I didn’t know about this one in big bear.

3:35 - exactly why you said it's a good thing to replace the inner axle seals! 😆

Awesome 3rd gen man!! A live axle is still better!!

What new gaskets are needed for this job?

Do you know if you can still fit 15" rims after the rotor and caliper upgrade?

Dude make more vids!! They are hella good

Does LT kits solve our LBJ problems?

Unbelievable, 3rd Gen!

Wow big flex with the working clock

What size tires?

Toyotas are a dedicated group. Always have always will

oh you meant Looong travel

time for lower tire pressures and bead locks...

Bro!! The 1 Ton 4Runner!! 🥰🤣

Dope to see some CV's in there! Most LT builds I see are desert trucks

Nice setup.

Does the 4 runner owner have a insta?

always replace head bolts Good video

What springs/ lift you running in the rear, I like the stance, I have the same kit but mine sits low in the front

This is an costly lifestyle but very satisfying I believe. I can’t wait until I go overlanding. I have a 4Runner also that I would like to build into a nice overland rig.

great video well done

7k front end

Is that coheed and cambria in the bg? I want that build.

Where you get the set from

What bulge on the fiber glass? And tire size?.

I used this kit on my camry 2.4 years and years ago, its been 140,000 miles of trouble free ownership after that. It really is a very nice piece of kit!

Let's go Brandon!

🤘🤘🤘

Il be doing this next week to my 08 hatch wrx s running 410 bhp can’t wait

do you think it will fail after you fix it do you think it's going to be permanent fix or it's going to go bad again ?

Where did you get all the stuff ?