❤❤

❤❤

Thanks for the video. Sir ntc heat ho ke machine off ho jati hai kya fault hota please tell sone solution .single card igbt machine hai.please

Hello sir.

Adress kaha parxa mero pani kharab xa

What name music

Yestai yestai videos haldai garnus daju sajilo huncha

Where you purchased this vacuum pump , share the address.

Hello sir hazoor Shiva, bds ns bhanni machine problem store filter Maa tar on hunn

Mesin lain jodda potkinx lain Didi kin r k ho problem sir

सर मेरे पास एक वेल्डिंग मशीन एलिफेंट प्रो की मिनी मशीन है सर इसके आईजीबीटी फट गए थे तो मैंने रिपेयर किया इज 60N60 के लगे हुए है मैने चारो आईजीबीटी लगा दिया पर ड्राइव वोल्ट 6 वोल्ट के आसपास आ रहे है सारे रेजिस्टेंस भी चेंज कर दिए फिर भी आईजीबीटी लैग्स पर 6 वोल्ट आ रहे है प्रॉपर 12 वोल्ट नहीं मिल रहे जिसकी वजह से आईजीबीटी बार बार उड़ रहे है सर बताए कया करे बहुत नुकसान हो रहा है

You put them on capton tape...... They will overheat. Capton is an isolator.

Those things are fantastic, but the downside to them is they are susceptible to dust shorting out the circuit boards. For reliability the have to be kept clean

I have kzubr 400mma welding machine its works fine when i shut off display is blinking and fan trying to work in intervals on and off when i cut a power, reley click one more time sometimes two and green ligh blink with display aprox 3 4 times what is the problem, in work is very good but this is anoying

good work sir this inverter is have one layer pcb

Sir can you explain other 2boad also l have Great youa the same boad which i watch, doyou have whatsup no pls give ,iam from kerala

Thanks bro after long time I fix today , because of you , thanks 🙏

सबै तिर फेक igbt, original igbt काँ पाउछ राना सर ?

Am working on welding machine with this same fault and it have no relay , I have tried fixing it but I have gotten it right but I knew voltage is missing some where around the small panel, please I need assistance

सर इसमें 2 कैपेसिटर में से 1फट जाए तो वेल्डिंग मशीन चलेगी 1 कैपेसिटर पर की नहीं

Hello bhai

Igp arko mospet kati no laagchh

What liquid did you used to clean the board?

Online ho rahi hai waterproof wali welding machine kya Karen

3:03

Cambie el rele y sigue haciendo lo mismo, qué mas podria estar fallando

Ye hi machine h mere pass

Mane igbt to dodara dal deya or machine to on ho gayi par output nahi nakal Rahi h sir

Good sir working

Sir tapai kaha Baat sir

Overheat alarm and solution

Please I am having power problem on my MMA 250 IGBT welding machine ( maxmech ). Once I play the machine it will spark. Please what can i do

Aapki phone nambar milega

👏👏👏

Pareho Tayo ng sera sa portable ko blinker din Ang display.

sar ji Salam walekum aisi machine I Hui hai Jo supply mein aisi laga hua hai na yah saaf tango wala to iska number aap bata de vah mere pass hai vah Jala hua hai

Bhai j mre pas isi ai h assalamu alaikum

Very useful and knowgable video. Thanks

kaha kitna volt ata hai check karna video plz

i have a mig 125 power light flickers fan spins slow , could it be the relay? why is there 300+v dc ? can you can explain or have a schematic ?

sir ye driver tester kese bnaye led wala

WOW !!

Current com ya jyada nahi hota pot kobadal diye hai kya kare please advise.

Sir do you have schematic diagram this welding machine ?

Sir do you have schematic diagram this welding machine ?

Nice

Very good job dude , I wish I was rich I would buy you a new Fluke and soldering station, you deserve it my friend. Best wishes , love happiness and health from Canada 🇨🇦

Sir namaskaar, diode,igbt, rectifier ok xa bt output voltage 15 matra dekhauxa kina holaa

When ur connect negative positive for testing..???

Good tiching karte hai 👌👍👍👍👌👌👍👌👍