it absolutely does, when you replace the stock intake with a high flow intake you are adding more air to the engine that is already programmed from the factory, to run more lean due to emissions (especially if you've added a high flow exhaust or even just slip ons). you definitely should get a tune after adding an intake to any bike really.
Mine wanted to charge me $1,200.00 to rebuild my forks (new fork oil)! Screw that! I bought all of the parts and tools for $700 and did it myself. Took about 10 hours over four days (took a while because I made a video of my job for YT). Next time it will take me about five hours now that I've done it already. When it's time to do the clutch, I'm doing that myself too.
Now that time has passed, do you really feel any difference? Is it an upgrade, better or worse ride? Also, was the Indian Clutch Shaft Arm worth it or a gimmick?
Hi, yes. I see difference. Much better and smoother shifting. My stock clutch was not perfect to begin with. It has been few thousand miles and I am happy with it.
Use Amsoil. I can't tell how much better my 2022 Indian Chief Dark Horse ran. Everything was better....The shifting, higher RPMs. Ran way cooler and sounds so much better.
Hi, I never had this problem, but heard of it. Could be loose screw with spring, could be anything, hard to say. I would probably get new clutch, address it, before more damages to your gearbox. Good luck, hope you'll fix the problem soo!
@@eurorealtors thanks! Is it a sport line? The bumpers look very stylish, do they look like that in basic model? I’m thinking of using plasti dip spray for badges but if not gonna work I will replace them same as on your video! Cheers
Hi, I heard an opinion, that after removal of front bumper it is neccesary to setup again front assist radar. I mean to configure it again. Do you confirm this statement? Thanks beforehand for your answer!
I would suggest to purchase an OEM from dealership. I do have a local concats as I work in the industry, they usually make a better deal for OEM parts and accessories.
@@jordanpierguidi1722 I have decontaminated the plastic bumper like you do before ceramic coating, do not you hard clay bar, it will scratch the plastic, find a painter who will threat it correctly, and use the filler, basic coat, paint coat and the clear coat. It has been a year and no problem at all.
Hi - a question - can you push back in the bumper if it’s pushed out slightly at the left hand side? Without removing it all? It’s not the actual black bumper but the surrounding housing
Hi, I am not sure, if I understand your question, if the bumper is out of the guide rail under left side panel (fender) or under left taillight, you can just snap it back, just be careful not to damage the taillight, make sure it goes into the right place with caution. Good luck.
Hi mate, have you had any problems with your badges peeling off? I changed my Octavia VRS badges but noticed they are starting to come loose. Is it better to use a heat gun before application?
Hi, I used 50 ml each. 3.0 = two coats for entire car and one coat for my Indian Springfield and still a bid left over. SIC = one coat and about 30 ml leftover.
Hi there, thank you. First time I am doing ceramic coating. It's actually very easy, the preparation is more difficult. I live near Prague, Czech Republic.
@@eurorealtors I recently had my first application as well. It went fine. You have a good garage and lighting, I have to work outside, but I manage still. Good luck in next applications too
Thanks for such a detailed instruction vid. I have a standard Karoq. And would love to change the bumpers to the painted sportline type. I just have to find some. Thanks
Hi, I am afraid so. The fog light has one screw and two buttons (inside) you need to squeeze to remove it out, and I don't see any way how you could reach it without removing entire bumper. It is really easy to remove the bumper, just be careful with the tail lights and bumper holders right under tail lights, the plastic partials could break off. Good luck.