Hi, my motor needs a slight push for it to start spinning , im using two 11.1v 40c 5200 mah lipos in series, any idea as to why this happens, same issue when i use a 35v PSU Thanks in advance
@@A-tech hii thanks for the prompt reply, I’ve tried 4 motors and two speed controllers, isn’t it highly unlikely for all of them to have the same issue?
@@A-tech im using two 11.1v 40c lipos in series….. And the motor runs without needing a push start when i connected a 11.1v lipo to a drone esc I just cant wrap my head around as to why the motor controller doesnt work
That looked really fun and performed well. I was thinking to make a hovercraft since I bought brushless motors that I can't use for an airplane due to local laws regarding weight. Also I have 10cm propeller blades. One prop plus motor and 2S battery etc. can do vertical takeoff like a drone so may be too powerful. Or I may make an air boat.
hi, thanks for the comment, they arent physically linked so they should be able to turn at different speeds ok with a bit of resistance, the steering angle on the front wheels is low which doesnt help, the way I put it together could be improved so the steering link bolts dont hit the frame, thanks
Hello, thank you for the wonderful video. I want to ask, does the STM32 cube program open the compressed folder directly, or should I use the VSC program?
Hi, I can’t seem to understand how to link this video with the hoverboard one. Like how do I get the connected ps3 controller to output to the DAC script and control the hoverboard?
hi, yes control the output of the DAC with the ps3 controller, it will be outputting a voltage, you can test it by plugging the DAC output into an analog pin and reading the voltage when sending different signals to confirm its working, hope this helps
I just dived into this i figured out how to flash and load the test program into the board. But havent find any quides how to set the board as a gocart like throtte & brakes. Or edit any files or somethimg like that been on to it more then 12h straight
hi, sometimes a break can help you get past things you are stuck on, I have a couple of motherboard hacking videos that you may find helpful, if you are ok with arduino you can manipulate the signals going to the boards to do what ever you want, hope this helps
@@A-tech i finally lerned how to select what i need and build program & upload the program. But now i need to find a way for throttle/brake and forward/neutral/reverse inputs.
@@A-tech can you please elaborate. How do they connect together if it running on just one Remote Control? That means the remote would run 4 wheels simultaneously…
hi, the wiring diagram is in the later part of the video, you can get a screenshot from that, the code is really basic, you can use the fade example to send a pwm signal or use a dac to mimic a potentiometer, hope this helps!
I have a working hoverboard motor (tested on another system ) , I have purchased a brand new 36v controller with lcd ( s866 ) brand new throttle and brand new hoverboard battery for my e bike project but I'm experiencing no throttle issues I have checked voltage and purchased 3 brand new throttles checked wires tried swapping around but still no throttle
@@A-tech yes I have seen the same thing ( thanks for the suggestion) , as this one ☝️ really puzzled me every thing brand new fully charged checked all cables etc , I guess it dose t leave much !
Cool... your TT01 seems to be powerful, hard to control at times. I lost control & crashed my TT02 due to tyer fly out during full throttle. Guessed super glue all tyers is the answer. Thanks build buddy~
@@A-tech i have 12v Esc and transmitter with controller from kids car , it will be nice if you can make a video how to do it , i wanna put hoverboard wheels to kids car so i can control it and i don’t know if 12v esc and transmitter from kids car will hold 36v
hi, the code is just basic pwm, you can get it from a fade example in the ide, I did another video with the controller but they are not that good, using the motherboard that comes with the hoverboard is best I think, thanks
Hi. How did this project ultimately turn out? Cant seem to find the next video. Cheers for sharing. This is perfect info for me who wants to build a scooter. ❤ Were you able to share the firmware that you had? Made any changes sense this one?
hi yes there is another video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7lScM__fiOE.html, I havnt done anything with the motors since, mostly been working on the rc cars, thanks
It's good to see honest thoughts about this printer. Today I smashed my glass too. It is very fragile when attention comes to 2nd place. As always, 99% of "problems" belong to us. Thanks! 😀
they should have just made them acrylic, I did hear back from them eventually and they have agreed to send me a replacement, might be worth sending them an email, cs@creality.com, good luck and thanks for the comment
@@A-tech Can you or @ThreeDPrintDesigns help me with something please? My door was shattered on delivery. I cleared all debris that I could physically reach, but when I check (by tilting my printer, like emptying shards into a bag for example) -- it's like there's a TON of glass like... INSIDE the printer. It's really weird, and I don't know how to get it all out, and I can't find literally anything online and the support team is SOOOOO slow to provide any meaningful assistance.