Thank you :), all of the right info with no fluff

Thanks you for the video! Snapped my belt same time my bracket broke off my deck. Temporarily holding the deck up with bungee cables from one side, so removing the deck was not an option this time around. Answered every question I had in regards to this process!

Dude perhaps not noticible cool temps but effencies in the mechanics which is to say not necessarily noticible change in tempture but the effect of how easier your unit has to enjoy working noticible in its operation not necessarily in felt changes..great video great narration

Thanks buddy. Just bought one and didn’t feel like trying to sort through the manual to figure out how to set it up so I set mine up by following your instructions as you set yours up in the video. 👍

Is that hairspray getting on the hair dryer?

Isn’t there supposed to be a 20° difference it’s 100° where I am. My AC is at 78. Air is coming out is 58° degrees.

I am about to vacume at setting waste but can't find the main drain to shut it off ......doest have to be turned off?

rain makes the roof cooler also... a shaded home will run cooler also.. also build a cover over the units and keep the in the shade... plus hose down the units rakes hours for home to catch up and cool down .. its a slow process but it does help.. insulation plays a BIG part....

My sand filter doesn't have circulation

you gotta be fucking serious i thought that was like some weird power box for the button i didnt know it was a box with stuff in it

Watching you fight the captive thumbscrews all the way out was painful 😆. Thanks for the overview!

Craftsman has the WORST customer service ever! They actually sent me an email when I needed service help telling me that there were NO service repair options they could offer, that they had NO parts or schematics to offer anyone tryin to repair one of these, that they had NO batteries to offer anyone needing one if they failed, and telling me to recycle my mower and buy something new!!! Luckily I was able to fix mine when it would not start after tearing it apart and trial and error efforts... I will NEVER buy another Craftsman product again. Like the mower and its accessory tools, but have ZERO ability to depend on them for any service or repair issue.... NOT the Craftsman of yesterday when Sears owned them.... Also, they got rid of entire V60 line if you have one of those products!!!

I can’t thank you enough for this! I’ve ordered all the replacement parts, so now I can do this with confidence! I LOVE RU-vid!!

Do you need pocket screws on rails and styles, or is the glue sufficient?

Thank you. All the other videos are worthless, except yours.

Im thinking it would allow the compressor to run longer before having to turn itself off due to heat.

Should never pick up an old shed floor without checking for snakes first

Thank you so much for this information. I went outside and noticed my brake lights were on. I got scared because it was after 11 pm. My son and I thought someone was trying to rob the car or something. I tried to turn it off several times and it wouldn't work. I watched this video and just held it in place with an old plastic discount card that I had around the house. It worked! I am going to get it fixed as soon as the sun comes up.

Well done mate

thank you!!! very helpful!

Thanks for your very good tips and explanations

I used this trimmer for the first time today. I found that the trigger is set too far back, so that I'm reaching behind me to hold the trigger. This caused quite a bit of shoulder pain. I like the trigger to be about at my hip, not behind me. I used a shoulder strap but when the trimmer felt balanced front and rear, that's what caused the trigger to shift too far back. I believe I got the right adjustment for the shaft length. ANY SUGGESTIONS?

Edging to this 🤭

Thanks so much,I have the exact same issue and hope I will be able to fix it. Appreciate what you do to help us all. Regards

Honestly the weight alone and stowage ability is worth it

Great info ❤

Might have been 10degree difference. But it did work. Better stats would be if you could put temp meter on both in and out vents before spraying and keep them running to actually measure while youre hosing it down.

Very helpful! Thanks so much. I’m a new homeowner & never had a pool. 😅

Watched your video many times. We got it connected and in the pool, but no rotation.

Can ego's 5mah battery be used in place of the 2.5mah battery?

Sink included?

This is not typical! The reason the paint came off easily is because Primer was not used. 99% of the time you can’t remove paint like that

Thank you! Great video

For anyone wondering what the torque spec is on the window, it's the German torque spec: guten tight 💪

Ridges on the gasket go up?

my MX6 has been working reliably for about 2 years. But I have now replaced the rubber bands and the "differential". I have now come across the information that the number of revolutions at 10 revolutions should be 20 to 25 seconds. What happens to my robot if it has 15 revolutions at 22 seconds instead of 10? So about 50% more. What could happen?

If it’s good for this dad it’ll be good for mine Getting this as a Father’s Day gift

Usually you don't have to take those thumb screws for the glass all the way out

Straight to the point! What’s not to like

And, that is another reason why I don't want a pool.

What was the tool with the hose that you used to remove the matter at the end?

The top rear right corner seems to be dented, is that shipping damage, or could it be bad QC?

Interested that in the specs it says min wire gauge for the 18K is 12 gauge but it recommends 10. Wish it would just say use 10 if that’s what it really needs. 🫤

Great tutorial. Helped me with my first-ever belt change. Thanks!

Stephenfixesthings-like it-very pro ,👐

Maybe they're low on refrigerant?

Internal combustion is done.

The big decider is the price,and depending on how rough your terrain is,it must just call for the durability of a gas mower.

Just happened to my baby today 😮 but thank god for this video I was worried the switch was stuck

Treat video! his is the only tutorial that worked for resetting my Brother to a new provider network. THANK YOU!!