They were faster than a drunk man at a pub i know that much! Seriously only down side was that direct drive which eats the wheel. Put a chain on it and it'd be awesome.
Can i ask question. Why my go ped when it rinning and press the break the engine turns off? What the problem? Everytime when running and used it. Thnks and advance sir.
Wow. You did the pad change totally bass ackwards. If you unscrewed the little pin at the top, the pads just slide right out. You don't have to split the whole caliper in half.
2023. Solid no BS video to disassemble an reassemble front fork assembly. Very clear showing the parts and how they came out. Mine was stuck (ok, is still is... but now I think I know what to do next.) The Allen bolt was difficult. After bolt, I couldn't tell what should come out next to disassemble. Thanks.
061723 Thank you for showing me step by step how to replace the batteries in my Go-Ped ERS 750 Hoverboard!!!! It's charging it's little heart out now. 😀😊🙂
Because it lasts for a really long time and does have rapid degradation of fuel capacity after many refills like electric does so they wouldn’t be able to keep selling as many.
I was told that too much weight on the spindle can slow the scooter down? Not sure if that's true? Too much pressure from spindle to tire makes it slower?
I have a go-ped Super Razorback V3 , I’m looking for information on it , when was it made , engine size , what the carb replacement # , is there a better carb for it ?
Yet another one who knows nothing about it and shows videos!!Sorry but you are completely wrong like HPI and tyant others with the adjustment of these carburettors FOR GASOLINE. HPI, like all other manufacturers of vehicles and engines that run on nitro, say exactly the same way to adjust the carburetion of a gasoline engine as one on nitro, which is TOTALLY FALSE. This type of carburettor, whether branded, Zama, Walbro, tillotson, etc., if they have a throttle valve, all fit exactly like a chainsaw. The low speed screw Lo=low speed. the hi=high speed screw. These are 2 circuits that supply the motor but be aware that from the quarter throttle open to wide open the 2 circuits add up. I explain to you as a master mechanic with more than 45 years of experience in the field. I am certified, Honda, Kawasaki, Yamaha Bombardier, Johnsered Stihl etc. I explain how to adjust your carburetor to perfection!!! start your engine and let it warm up to normal operating temperature for about 3-4 minutes. Let your engine idle because it is absolutely necessary to start by adjusting the LO screw in this way. What is needed is to find the rev peak by turning the lo screw very very slowly (to allow time for the motor to react) either clockwise or counter clockwise. clockwise and the regime will change. By turning the screw in one direction or the other find the point where the rpm will be the highest (always turn the screw lo and if the rpm is too high for idle, lower it to normal rpm with the throttle screw) and once the speed peak has been found, enrich (anti-clockwise) a quarter turn. For high revs do the same but be careful play quickly with the top screw because at high revs the engine reacts very quickly and leaving it too lean at high revs could damage it. Once you find the maximum RPM, add a quarter turn as you did for the low screw. If you listen to my advice, no one on this planet can do better than you. Ask any good chainsaw mechanic and they'll tell you I'm 200% right. I repeat the reason for starting with the lo speed screw is that at full speed the 2 circuits provide the total mixture then once the hi speed has been set if the person subsequently readjusts the lo speed by getting poorer (clock wise ) the total mixture WILL BE DECREASED. After a tank check the color of your spark plug spark plug best color is medium brown. The spark plug talk by by its color
Hard to be sure from this video, but looks like you might need more rebound damping on the back and a bit less pre-load and compression damping on the front. Really nice work. I really like the steering angles and range of travel.
Ciao dall' Italia 🇮🇹 volevo chiederti se le batterie al piombo del goped che hai messo vanno bene e poi volevo sapere se il caricatore delle batterie vecchie funziona per queste batterie al piombo grazie 👍
061723 Hi there Italy!!! I just replaced the batteries with the similar lead based batteries and they are changing their little hearts out right now as I write this!...... Ciao Italia!!! Ho appena sostituito le batterie con batterie al piombo simili e stanno cambiando i loro cuoricini proprio ora mentre scrivo questo! (Google Translate)
When replacing the inner tube, sprinkle a little talc powder inside the tire and use a paper towel to spread/coat the inside of the tire. Dust a little on the inner tube and rub a light coat over the whole inner tube. Slipping the tube into the tire will be easier, and when inflating the tire the tube won't get twisted in the tire. Add a little air first, bounce the tire, deflate and then pump up to final pressure. Same as you would when repairing bicycle inner tube.