Soot is causing it to turn black does that have anything to do with ERG

*Maaan whatever that roll is for the thermostat was a life saver. Got it on and didn’t have to take the extra hoes off*

Mines is not going down at all it bubbled up one time and im still pumping it after i changed both the fuel water separator filter and fuel filters. The prime is working but its not going down

🙏🏿❤️thank you brother

🤦‍♀️🤦‍♀️🤦‍♀️🤦‍♀️

Don't listen to this guy he is absolutely wrong

Broooo nooooooooo!!!!!!! Don’t listen to this goofball

FYI…With ABS systems it’s better to collapse the pucks by loosening the bleed screw to prevent damage to ABS system and also gets rid of the bad brake fluid that has been close to the high heat! Nice video!

Using the tube in the box that looks like a toilet paper roll is the best and fastest way to compress the thermostat.

I swear Chevy intentionally makes everything hard to get to. This will be the first and last Chevy I buy.

Leave that man alone man. He driving a Saturn cut him some slack

W-o-r-s-t. Worst. If you can't spell, ask somebody who can. You will get more views if you do not distract viewers with mistakes in spelling and grammar.

That spelling is the worst I have ever seen.. it's brakes not breaks..

The proper way is called bench bleeding with the proper tools, bleed the master cylinder before putting it on the car.

Do you have to drain the coolant first?

Thank u very much, this was very helpful video.

Great video, But when you expose your intake manifold, please cover the opening a Oring from the injector could have felt right in your valve housing and into an open valve and into the combustion chamber; god forbid it be something like a socket falls in. Game over you have to tear down the block

Blessings and great info thank you much, just need to find my cylinder 3 misfire and my fuel locate and injector #3 not quite sure if I change the right spark plug and coil because cylinder 3 misfire still came back up, will look into some more but off to doing more homework any help or comments it well appreciated thank you much and God Bless

I hope you have a jack stand under the vehicle when sliding your feet under the vehicle

Home boys paint is peeling....😂 thank you for sharing good way to do it walk away and let gravity do it...

Peoplemake sure u dont let ur clipper hang by the line like this or yall dont be up at the cheap joint again

Do i still have to bleed the rest of the brakes on my 85 grand national??

Easiest video on YT. Thx!

Thanks for uploading a video and taking extra time to help others understand the steps.

Unless you want to replace the front end of your car don't do it like this.😅

no explanation why you are removing them?

Make sure that the rear end vent tube is clear or non obstructed also.

All of it 😂

U skipped the gettin the ball joint part

Definitely not a good way of doing it

Hey bro I have a 07 international 4300 and can not find the brake pedal switch location. Any help?

Wow 😳

Well...trying to bleed a 2003 Jeep grand Cherokee master cylinder and before a min was up fluid was coming out easily

Do u turn on the car or just push on the pedal ??

New sub..good video and will be changing mine this week when parts come in

I mean you can weld it, but since it's broke off and cracked it won't hold very well and the structural integrity is compromised Just put bubblegum and duct tape on it and it'll be fine

Sure you can weld that! I know I can’t… 😁

I actually use some JBweld on a crank case of a motorcycle. I would assume this would be no different. Just slap a large piece of JBweld over the hole then hit it with a pneumatic sander once cured.

I would try to solder it.

Follow-up needed!

It's actually easy to weld cast aluminum

The POS is going to sell it to someone else. He’s going to get 10 fold what he’s putting out. Disgusting

still gonna say you did it

Good luck, I want to see a follow-up. Cast is its own animal.

Cast can be welded but it's not a great idea

Thanks bro im a Diesel mechanic for 1yr and a half this helps me out alot appreciate it bro keep up the grind💪

That is the drum .just worn-out 😮

Bro, in 28 years I ain’t seen nothing like that😂😂😂😂

Guessing that there hasn't been any fluid going to that wheel cylinder in a long time

Mofo went from zero to infinity on drums