Your lungs had to be coated in the stuff!

👎🏼👎🏼👎🏼

Yo vanilla!! Kick it one time boooooiiiiii!!

Do a rubie dt10 vs the ridger 10 in and tell us its rhe same saw !

Hi there, really the air compressor was running at all capacity? Filled the 6 gal tank and 150 psi? It is true I’ll buy one of these. Wait for your answer. Thnx

can you get grinding discs for it too ?

So.. Zero cons as expected from SIGMA .. i love working with SIGMA already almost 21 years now

What type of thinset would you use for marbel tile

What if I need to erase the mark afterwards?

how do you know its safe to cut the studs? also, do you just grout everything? isnt there suppose to be silicone on change of planes?

im fucked, I have to do one next week :)

My favorite vacuum for my window cleaning business, my only gripe is its really loud

Its the best tool for mitor cuts. Its hard to explain but they comw out better than not using the tool.

😂 " that's not working"

Modified or Unmodified thinset? Using GoBoard for my application and their "help" line says thinset. There is a difference and you're merging wood with a waterproof backer board. Any thoughts on which is better?

Ola como compro uma Riscadeira sigma estou no Brasil

Many thanks! Was on RU-vid specifically looking for technique to rip longer pieces on the wet saw. Need this for my 43" curb as I don't trust myself to make a straight cut that long with a grinder. Kerdiboard scrap, a big speed square, and done, ready to polish.

Спасибо большое закажу комплект я из Россий ,есть своя швеиная фабрика ,будем выпускать аналог по цене дешевле😊

I use the Makita on grout joints to make a relief cut before I bust out broken tiles in the back of house at chick fil a. I can't ise a grinder because it's too much dust even with a shop vac...it cuts the grout better than the ceramic or porcelain . But definatly small jobs or a lot of battery

So where does the water feed come from. I got a used one without instructions.

You forgot the cordless worklight or fleshlight

Multi tool and painter's tool are good to have.

lol... you left out the angle grinder. you did this to get people to engage in the comments LOL smart

no back buttering ?

Will this work with grout as well?

Laser is really hard to see. I rarely work at night so i need something which works during day. That one is not bright enough

What a joke, it barely sprays.

That works fine for glass, but how does a person know if they've vibrated the tile thoroughly to have achieved sufficient adhesion when you can't see through the tile?

Need a video for the Milwaukee VS Dewalt Variable Speed Grinder for tile work. Great video though.

Look like you are scared to use it

if you shut down the ac, it should power the microwave. you need at leastn of 3k watts, which is about equal to a 30 amp rv. 2k is pushing it

How did you connect the DCV501HB 20v Vaccum (extrator) ? hose doesn't fit exactly. Do I need some connector?

thanks for demo, but why not show 1-1/2" granite countertop cut?

thanks for the video. I have a question. We have done the pitch 1/4 inch per foot on the mortar which under the liner, do we have to do pitch again on the bed which above the liner?

hi what cutting depth does the machine have at 45 degrees? I mean can 2cm thick tiles also be cut danut?

You made and saved my day !!! THANKS

I hate the schluter trim. Doesn’t anyone miter or do the marble trim anymore?

I noticed you protected the floor, tub and toilet. But you put all your tools on the vanity countertop. Most customers would have an issue with that.

When 32nds count that lazer will make it worse.

Do you need a variable speed grinder? Or will a normal grinder work?

Is the DeWalt and rubie the same saw ?

Hi ! What type of trowel did you use for this large format tile

M

من اين نحصل عليها؟؟

Why do people push the handle up to top To cut tile and then drag back down to break?…when you push it up just break it while handle up there

Good video, but I just have a question: Can a DIYer install 12x24 tile with 1/16 leveling system ? Or is it too much ???

Great job

Adding in the cost of the Kerdi Board and Kerdi Band seems to make this kind of a wash, especially if you consider your time worth money. That said, the original curbs need to be trimmed either way.

Nicely done ! I have this saw I love for everything you just explained. Please note- you will need to buy different colored blades depending on your material. Also I had to call their customer service tech support and someone actually answered the phone ! So their customer service is excellent !!

in your "links below", for your laser level pole system you link to a Johnson product, but in the video you crank the pole up.... what tripod are you using that has the hand crank up/down? thanks