I loved your video! I always wanted to see how to link a 2-hand control in an rc car (is it possible to connect this transmitter and its receiver with any helicopter from amainhobbies, horizon hobby, rc mart? (or any helicopter that is not from aliexpress or banggood) ?) great contribution is a genius
hi I know that its been years you made this video but I can't get my wltoy v911 to bind I followed all ur steeps and still nothing,,,I have an flysky fs i6x till my can it work
Nice video! I was wanting to know, is the v911 nicer to fly with a proper Tx? It looks nice & smooth in the video. The standard one feels a bit vague to me especially in yaw. I've been researching aftermarket Txs for my heli which I can use on other models too. This Tx is one I looked at & the more expensive Frsky Terranis, but didn't know if they would bind to this heli. Some of these Txs now come with a module bay on the back of the Tx, allowing for a multi-protocol module, which will bind to pretty much all models (apparently!). It also looks like fun playing around with the settings like that!
so is your fpv transmitter and receiver can connect with smartphone and the camera.............................and if i use 5000mah 3s lipo battery can it fly high at sky..................and how much volt i should use...plz ans me with details...
I’m having trouble with my setup. I have the exact remote and the exact controller, I just can’t figure out what I’m doing wrong. Can you list what you did and how everything is wired?
Did you modify this cleaner that it moves the water with such power?.. Other videos with the same name and model on RU-vid bearly makes a sound and doesn't move the water as your cleaner does.
No matter what I tried, the transmitter will not control my planes. I set up the controls and each stick on the transmitter show correct calibration, but when I try to launch nothing happens and the transmitter icon shows controls in the wrong position
Hi. need some help with the pinout please. I have a MWC 2.5 and want to use it in an RC plane. i just cant seem to find an clear pinout assign for the servos,please help
don't set the throttle hold to on and 0% if you accidentally knock the switch, your throttle will be killed and the heli will drop out the sky like a stone! all you need to change from the default settings in the tx is to turn afhds2 off and just have afhds (something I didn't seen in this tutorial) if you don't turn off afhds2 off your v912 will not bind. leave gyro off, leave throttle hold off, leave mixes off, just set your duel rates so you have a high and low setting and reverse your forward and reverse channel as it's wrong on default.
Hi! what to change in config.h (MW 2.3 i have and Arduino pro mini is the board)to use it as flying wing FC? I have GY_521 sensor to have gyro and accelerometer for stable mode too. what I set so far in config: #define FLYING_WING #define I2C_SPEED 400000L #define GY_521 #define GYRO_LPF_20HZ According to schematics A1 is right servo, A0 is left servo, D4 is roll input pwm channel, D5 is pitch pwm input channel, throttle could be a passtrough, D7 is the aux1 probably to set flight mode stable/manual, for the i2c A5 is SCL, A4 is SDA
Hi, there is some solution in this thread www.rcgroups.com/forums/showthread.php?t=2554250 servo[5] = axisPID[PITCH] - axisPID[YAW]; // Full(VTail) servo[6] = axisPID[PITCH] + axisPID[YAW]; // Full(VTail)
do I need it for #define FLYING_WING too? I thought it is only needed for AIRPLANE type, but I will solder things together connect servos and try it out, thanks.
Is your DYS 4215 the same as the RCX 4215-21..? Both 650kVs but the RCX ones only cost US$16 a pop despite putting out a whopping 1600g of thrust @22A on 4S LiPos. I intend to put this on my S500 airframe to swing 1170 props.
