Dedicated Caravan information channel - delivering hints, hacks, tutorials, information, and fun for your education! Subscribe to keep up to date with new release products, events, and competitions. Join the clan now by subscribing and turning on notifications.
I have just watched this video as I need to get my awning skin repaired. The stitching has come apart at the track side on the van. Once I have the skin resewn is the process the same as replacing a skin bearing in mind I won’t have a second skin to use as a guide?
When ordering vinyl what happens if it comes folded up in a package and it is full of creases which could cause holes. Should vinyl be sent rolled up in a long tube and therefore no creases
We take GREAT care in packaging our vinyl, however, the vinyl will still come with creases from the packaging. To get the best out you need to unpackage the vinyl and install it as soon as you can to allow the sun to heat the vinyl which helps remove any creases. Rest assured our vinyls come with a 5-year warranty.
Yes, we are one of the few companies that make custom Annexe for this particular vans, if you want more information please check out our website: www.greatannexes.com.au/ or contact us on 1800 612 672 or info@greatannexeco.com.au
Great video, nice camper! What size is the connection of the gas pipe to the Varioheat? I thought it’s 1/5“ left, but it’s something slightly different.
Theres a few reasons, i resheeted/recycled old sheet on my caravan (1974 aluminum frame millard) because the front was stone chipped with 3 5cent coin size holes. while i had the J rails off the majority of the caravan i re-wired it so its easy to repair in future because brake and hazzard light wire ran through the walls and then roof so i welded mounts to bolt a 20mm box tube to chassis to hold and protect wires while being ran under the caravan. I also insulated it with more modern insulation and added extra (wood) noggins to the aluminum frame to give it more rigidity when towwing. Many other reasons but mainly to waterproof and replace old aluminum or tin sheeting
Most of the awning sites want the distance from arm to arm which is usually a foot or so larger than the fabric. Most sites i looked at explained this and tell you what size to order and where to measure and also the actual size of the fabric itself.
Great easy to follow video. I've had a couple of garage roller door jobs and know that spring tension and fingers don't always mix well! Excellent instructions with each step explained and shown clearly. Was a bit apprehensive of doing my own awning (and nearest service is 650 km's away. Your awnings were on top of our list and the video on how to just clinches it. Thanks
I was afraid of the spring also. I ended up replacing mine without messing with the springs and rivets. I made a video on my channel if you think it might help you.
That is so awesome!! Makes ya wanna race out and buy an old van and do it up. What is the shiny white acrylic looking stuff you put on the ceiling and some of the walls? It makes it look so modern. Thanks
Hi Geoff.. thanks for the comment. We used a gloss white ply veneer sheet. Great to help a small space to feel a little bigger. Available from most plywood suppliers
Removing the second spring is a glaring omission in the video isn’t it because he tensions both springs! I did mine with only one spring removed (the ratchet side) I could not see a reason to remove it.
Yes, both are tensioned. When I release the pressure off.. it is de-tensioning both springs at the same time. Removing both is required on Dometic awnings, whereas Sunburst and Carefree can be done removing one only. Removing both is great to check the condition of the both springs, as surface rust can be an issue. Spray both springs with lubricants regardless for better performance of the awning. Tension will still need to be reapplied to both springs.
Cold air sinks! With having the vents down low does it still work fine or is it advisable to mount the vents as high as possible. I’m looking at mounting 2 in a 40ft bus, 1 in the bedroom and 1 next to my dogs bed up front just to take the edge off.
The position of the outlets are determined by the RV layouts etc. Higher is better, providing you can get the ducts up there. The outlets are a angle fluted design, so generally you can turn them in any direction to send cold air up and out. Hope this assists
Hi Steve… this unit is 3.5m and Fiamma do not include it as standard for this size, however provision are present. Rafters are included from 4m+ in length.
Great video thanks. One clarification is the locking pin referred at time 12:45 . As this is removed later (video time 14;40) is there any special pin needed or just a nail that fits snugly in the hole and is then slid out using pliers? Thanks again.
A nail is fine… just ensure it is about the same diameter to the access hole or as close as possible. If you use anything too small or soft, the spring pressure can bend it making it very hard to remove. A 5mm steel rivet shaft can also work.
Did the middle support come with it? I've seen where the F45s comes with a bar that's tucked away with the legs that helps with supporting the middle of the awning with snow/rain.
Hi we have the basic Fiamma F54 annex on our Jayco Eagle camper. In the video you state that the anti flap bar fits into "a clips in the top container". Question - is the clip already fitted or is there a modification required? And, are the additional support poles included with the anti flap kit? Thanks, Garry
Hi, prior to putting the tension back in the springs, why not reassemble the drum into both arms, then tension both springs at the same time safely relying on the ratchet to stop the drum unwinding, or am I missing something? Cheers
Nice install. I prefer my Diesel Heater, as it offers a Clean dry heat, which means none of the humidity and condensation that you can get from gas heaters.
