If you can give me some more information about your type of radio, receiver and FC you are using, I can see if I can help you. Please note that this video is not for configuring inav, but how to have graphical telemetry with Radio, crsf, and fc receivers that support it.
@@MrSalvoFly Thanks, it's a RM TX16S, RM RP4TD RX, Speedybee 405 Wing FC. Setup radio according to Painless360, RX connected, telemetry etc. No receiver map results in INAV. ....well figured some out, model mismatch. replaced original receiver and got mapping now. We'll see about controls in a bit. Thanks for responding, I might have a question for you later.
@@MrSalvoFly ohh okay! I am strongly considering this for my first vtol as I'm trying to move on from traditional quads.. I want to run the skydroid c12 which is a hybrid thermal cam and gimbal combo but it weighs 117g and may be too much. I'm planning on running triblades like the ones on the zohd altus and pi zero with px4 as I need an fc I can pair with AI
Look at my VTOL playlist, you will find all the videos on the Manta that can help you. But consider that with a 4s 1300 mah battery you are already at the weight limit to not be a brick.
Hi, the plane is sold in the ARF or PNP version. I took the PNP version you only have to put the battery and receiver. You can find it on Banggood or Aliexpress
No it is not provided. The recommended battery to buy is a 4s 2200 mah. I bought 2 Turnigy nano-tec 4s 2200 mah and in terms of size and balance of the aircraft they are fine.
The servo that regulates it is built into the right side of the rudder, while in the front fuselage there is the second servo that turns the wheel. Both servos are connected with a Y-cable, which I connected to the FC Lefei sparrow 2 on channel 4.
The rudder servo horn was manually pushed forward to save space for packing like the other wing servos. If you supply 5 volts with a servo regulator you will see that all the servos are positioned at 50% and the supplied rudder tie rod is the right size. The brackets have a slightly larger hole. Put the rod there. Uniball goes square side in the first hole at the top, also for the wings.
Ciao, tra il v3 pro e il v2 (rosso) ci sono differenze: 1 ha la 5v che alimenta la ricevente, (no servi ci vuole esc canale 3 motore collegato) 2 slot per 2 cam con switch channel, 3 l'osd ha qualche parametro in piú tipo la temperatura dell'Fc.👋
Hi, I'm using a Radiomaster Tx 16 Mk II with a Radiomaster Rp3 receiver. I mounted a Lefei Sparrow2 flight controller without GPS. I bought 2 4s 2200 mah 40/90 c batteries. Tomorrow I will make a post with photos of the F16 ready to fly.
Hi, read the FAQ on the Sparrow pro manual that you can download from the Lefeirc website. Find out what to do if you install one or two cams. By default it is CAM1 the channel is enabled by default and does not appear in the OSD settings: Cam Channel.👋
Have you wired her up yet! I got my today...now put it together. I open up to take closer at the EDF it doesn't label the brand of the motor no info what so ever???
Hi, I made a post about the progress of the work today. You can see it in the Community section. I glued and connected the movable surfaces. I put carbon rods in the wings and rudder. I tried the servos. I have to put the flight controller Lefei sparrow 2 to complete. Motore: Motore brushless 2848-KV2600 Ventilatore canalizzato: 70mm, 12 pale
Buen video! Tengo exactamente el mismo setup con una duda! Yo conecto mi receptor ER6 a la speedybee por el conector de arriba, y en la radio aparece Crossfire... No deberia ser erls??? (Me funciona todo, telemetria y demas) Solo por saber la diferencia!
Hola, el protocolo del receptor Radiomaster Erls (ExpressRls) funciona como el protocolo CrossFire (CRSF) Si ha instalado Lua ExpressRls en su Radio, puede configurar Radios, módulos y receptores.
Hopefully soon, I have to do some reinforcements and order the 4s batteries. It was on sale on Banggood. Now you can find the P 51 Mustang of the same brand on sale.
Ciao, come ti trovi? Ho visto alcuni video che dicono che ha bisogno di molti accorgimenti per poter volare bene. Specialmente nella fase di transizione vtol.
Ciao ho fatto 2 video in merito al volo del Manta. Soffre il vento in modalità drone poichè ha molta superfice investita. E cosa non fare prima di decollare. È importante avere la cam/visori o aver installato Yaapu telemetry sulla radio. (trovi nella mia playlist dedicata al manta). Link video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-75Izldr5yDI.htmlsi=9eqxM7nfVeGrX4qn ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-SKOyz2j7Noc.htmlsi=WxuuH9sjogfLV1MN
Hi, download the manta 1 pdf, which you can find in the video description. You find a photo with pads circled in green. M6 M7 and M8 the + and - Connect the new servo on M6 and then the output of the example channel 8 with slider on the radio to move the cam must be configured on M6 with Mission Planner.
If the GPS does not have a compass, orientation is not needed, and the direction of the cables does not matter. With the compass you can follow orientation using betaflight or Inav.
The GPS supplied with the Sparrow does not have a compass. You can orient it however you want. Respect the part with the ceramic antenna facing upwards.
Hi, I still have to test it, but I'm confident because I installed an FC that works well. The Fms fan is not cylindrical and you have to dig a groove. The lower part with the magnets has been glued.
Hi, If you bought the FIMI Manta, look for the playlist dedicated to VTOL on my channel. There are all the videos and various Radio and Flight controller settings.
Hi, you have to assign a channel and switch related to the three-position radio and configure to OSD. Please note that some depend on whether you have a GPS fitted. I only use the three primary functions. Balance, Manual and RTH.
If the GPS does not acquire at least 7 satellites, the RTH function is not activated and it goes into maintain height mode. The primary switch must be set to 3 positions and is mandatory on channel 5. You will get Balance, Manual and RTH/HOLD. If you use an sbus receiver you have no problems. If you use a CRSF receiver like expressRls. watch my video how to get full resolution at 3 positions on channel 5. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7bXPKSoeACM.htmlsi=AgRY5urfhu386OdI
Hi, I have a problem with the voltage sensor in my Speedybee F405Wing The value in INAV is up and down 13v~20v (I use 4S battery) I have changed the battery but the problem still occurs I am really furstate because I really like long range flight Do you know what component that I need to check? (It seems I broke that during soldering the cable) Is there any external Voltage Sensor available that can be sent through our Remote? Would it be possible for us to parallely connect the Receiver (Matek R24D) to Flight Control and CRSF to PWM converter The idea behind that because I heard we can get Vbat tellemetry to my remote using CRSF to PWM converter But at the same time I stil need OSD and Waypoint capability from Flight Controller
Hi, I'm sorry about your FC. Matek System produces converters from ExspressRls to pwm which have the vbat pad to be connected to the + of the main battery. The OSD functions remain.
Ciao ho visto che dalla pagina principale hanno tolto i link per scaricare i firmware, collegati alle radio. Ma se vai a fondo della descrizione del video trovi il link funzionante che ti scarica il firmware della pocket.
Saludos serías tan amable en confirmarme si se puede se volar con un radio Elrs(2.4) litle radio3 pro o o debo colocarle algún módulo para después programarla
Hola, si compraste el Fimi manta Vtol, la versión FC, el controlador de vuelo ya viene programado para receptores CRSF. Los receptores ELRS utilizan el protocolo Crsf. El software instalado en el controlador de vuelo se puede configurar con Mission Planner. El VTX configurado por defecto es Digital, como DJI u otro. Si quieres instalar una cámara vtx y analógica, sigue mis otros 2 videos dedicados a Fimi Manta.
@@MrSalvoFly un millón de gracias , es usted muy amable con seguridad vendrán otras consultas si usted me lo permite , realmente estoy lejos de que me llegue el VTOL en mi país acaban de cerrar todas la importaciones debo esperar que las normalice para traerlo pero lo haría para volar en analógico primeramente
Hola, para volar en analogico hay ofertas en Banggood, para vtx y cam. A veces encuentras ofertas en visores o gafas de Eachine. Si tiene preguntas en el futuro, simplemente pregunte. Saludos
