That's two of you that haven't shown how to slot the side panel into the bracket ,is that because it's a pig of a job? My panel is 6'x4'

I cannot get caulk gun to work!, what am I doing wrong?

I have a bathroom/shower cubicle to resilicone so hugely grateful for this video. Thank you.

Too much talking, get straight to the job, works better

Fantastic tutorial! Your step-by-step guide made the process so clear and easy to follow. I especially appreciated the tips on preparing the surface before applying the silicone caulk

Thanks bro greetings from Virginia. Where we can buy that tools?

i know how he could double his wage, stop fucking using all that paper towel

Thanks for the good and helpful tutorial sir! 💯🔥

thanks for sharing the knowledge, I have just rechanged the valve. It's really useful. Thank you!

Very cool!!!

Thank you.

You have saved me a couple of hundred quid buddy. Thank you. Great vid that took a total beginner through the process. 🎉

4 years late, but shouldn't there have been a waterproof tape on the Jackoboard in that far corner?

Just did three sides of a sink sitting on tiles. Very pleased with my first time attempt. Took less time to do it than it took to watch this video...although I did watch it twice. Thanks.

شكرا لهذا الشرح لقد استفد منه👌👌👌👌

Superb. thank you.

This is a perfect example of you don't know what you don't know. How are you teaching this.You don't even know what you're doing.. You explained almost everything except for cleaning the pipes, putting compound on the male thread, not female and which way the valve goes with the arrows. And no its not self explanatory. It's vital to know this and probably most DIY ers wouldn't even think to make sure the arrows are facing the flow of water. Just awful advise. I wonder how many floodey their homes from this.

Thank you, now that is afternoon to detail!

It is wrong to do compound on the thread. The thread only pulls the olive onto the bare copper, the thread does not seal. When turning, the olive is formed on the bare copper. Copper forms a positive fit on copper, which creates the seal. No compound is allowed in there.

My out side stop valve is ceased any ideas how to free it up without calling out the water board

A job I really hate. That stuff stinks and sticks to everything. God knows what the leftovers do to the environment. 🤮

That is so fast? I have mine taking 1.5 hours for a hole.....very slow

How do you make sure that the hole you are drilling remains a single horizontal and vertical plane without deviating?

1. you took too long to get the actual Drilling 2' You can clean your diamond tool with aTrue Red Diamond Blade Dressing stone, to get more use out of it

so much materials wasted. if you know how to cut the tip and angle the silicone gun properly as you lay the bead then you won't waste so much. The correct angle must have the tip ahead of the barrel of the caulking gun and not the other way around.

Brilliant video well done. So refreshing to see good videos like this👍👍👍👍👍

I see so many.vidros where ypu recommend soapy water, to help.mold the silicone. However youd NEVER induce any water or soapy solution . just know how to ypu the edging tools ypu have and ypu wont need that soapy watery mess. Ypu inducing water and soap into the silicone mixture period.

Thank you. Problem solved. Took more than five minutes. First my seat had two horizontal silver buttons. Secondly the caps didn’t just pop off after seven years I had to persevere to get a knife blade just to lift the cap without levering the pin assembly upwards. Finally I realised that leaving the seat central was important so I had to release the other pin/cap loosen the tight bolt and position both before retightening. Piece of cake once you know how 😃. Thanks again

You forgot the word 'not' in the title. 10 minutes to silicon a shower! Watch the van isn't overweight after u put that excess silicon in the back 😂

Thank you so, so much. I am off to drill mine tap holes now🤞

Thanks Kris, this is great info, helped me out massively. How long do you leave the primer to set 1 to 2 hours before adding the adhesive, i am using mapei rapidset adhesive ?

I had success with starting the hole with the expensive diamond bits and finishing the hole with a masonry bit.

YOU'RE FIRED.....GET OUT.

A wise man can discern when some one comes to the end of what they know , and start making up the rest.

Thank you 😍 my bathroom looks fantastic with your help xx

Surprised you don’t keep going with this Gonzo? Stacks of views on previous videos!

Worked. Thanks

No tanking , no classi seal , 🤔

Thanks for this video. Right to the point with no nonsense. Very professional. I have to enlarge the mounting holes on my mom’s toilet bowl bc the replacement screws are larger than the discontinued standard ones that hold the tank. I’m shaking in my boots bc the unit is about $1000 and now it’s been discontinued. I can’t mess this up! Thanks again.

8:09 are you going to have a removable panel on the back of tha toilet? How is the cistern going to be accessed?

I thought you first fix the shower tray and then tile.

1st class

Thank u for this. Finally, I got my wobbly toilet seat fixed. 🙌😏

Try not putting as much on in the first place and save yourself money and silicon, otherwise helpful.

Thanks for the tips about silicon, but what's your latest thoughts on David Moyes?

Jointing compound seems much better than ptfe tape because the tape is very fiddly and fragile.

Beautiful thank you so much for your help

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-_DI4hfHM_Hg.html

LONG WAY FROM THE WEST HAM CHAT I THINK.LOL

I'm a professional. To be able to apply silicone just like an experience professional caulker, I have been watching many videos on how to apply it perfectly. This video probably was the 20th one that I watched over about a week time. I gota say that this video is the most thorough one. Although he applied silicone roughly purposely, he taught us how to manage it. Very well done. I am saving this video.