En una TOS vertical N3, no se acopla el vertical o se acopla y no se despega y funciona en simultaneo con el horizontal o transversal. Tiene alguna solucion para indicar ?. Gracias.
Hi, could you please provide the number of teeth of the head driving wheels and the diameter. I bought the same milling machine but I am missing the head drive wheel. Thank you in advance for your answer. P.S. Good job
At the finish, a large powerful tool, to deliver work at precision. Very nice project. Excellent to finish at operation. Thank you for posting. McGary *Washington state. US
Hello from Washington State, US. Very nice to see your machines with paint and the shop building. I am semi retired but have been cleaning and fitting a 1938 South Bend lathe. Fair winds. McGary
I love refreshing old machines. One of the best uses I’ve found for a digital camera is to take as many pics of the disassembly as possible. Back in the days of film it was to expensive and took too long. Now you can take a thousand pics for free and have them for reference during reassembly.
If I can offer some advice, then I'd suggest that it maybe best to split the video sequence down into segments, that are organised into logical steps, eg pre-cleaning, disassembly of head and reassembly/repair, knee dissasembly/repair,.....prep and paint, electricals, etc. This way the video can be much longer and more enjoyable and engaging for the viewer, rather than it appearing rushed. I know it's hard to make time these days, but sometimes it's best in the long run to take the slower route(part of learning the craft of machine tool fitting) - Liked and subbed. :) BTW TOZ make excellent and robust mills and lathes, which are always accurate and reliable, but often sadly abused by incompetent operators' for that reason! Keep safe and well.
Por favor, não apague este comentário. É a única forma que tenho para divulgar essa vaquinha. vaka.me/2186417 Peço a ajuda de vocês para conseguir adquirir um torno mecânico. Se não puder fazer uma doação, agradeço a gentileza de compartilhar essa vaquinha. Que Deus abençoe vocês. ru-vid.com Israelcosta@gmail.com Grato!
Zdravim, pekna praca. Chcel by som sa spytat aky hruby lexan a jokel ste pouzili pri ovalnom bazene?+ Tie strieborne listy v oblukoch sluzia len na prekrytie spojov? A akou farbou ste to natierali aby to bolo odolne bazenovej chemii? Dakujem
Díky, síla lexanu 10 mm, jackel 20x2 mm + pasovina 20x4 mm která podpírá Lexan, nerezová lišta 0.8 mm, která drží lexan na místě. Barvu mi doporučili, tu která se používá na nátěr střechy, název už nevím.
Cześć,aż dziwne że mój komentarz jest dopiero pierwszy. Ja swojej tokarki aż tak nie rozbierałem do malowania. Chociaż gdybym miał więcej czasu,to bym wszystko porozkręcał ;) - Pozdrawiam ,Paweł.
Yes, I have the same one... :) At the moment I have some issues with clutches and magnets and I need do dismount and adjust them. In fact, I did the same years ago and that’s why I need some docs to dismount as less as possible. I lost documentation😊 Can you please take some photos of manual and send me, somehow? Thanks a lot!
Osvětčilo se mi odstraňovat tyhle staré nátěry louhovým odstraňovačem nátěrů LAKTOSAN. Natře se to štětcem, pár hodín počká a pak opláchne vapkou. Smeje se to až na litinu. Ušetří to strašně práce. Akorát bacha ten louh stejně dobře žere i kůži.
@@workermilan5257Akorát opravuji je to LAKOSTAN, m konzistenci gelu. Musí se k tomu koupit štětec na louhy, obyčejnému během minuty zmizí štětiny. Určitě nepodceňte ochranu očí a rukou, stačí odstříknutá kapička a je průšvich, rozežere to kůži i maso a nic při tom necítíte. Lepší je to dělat venku, pokud by to zasychalo, je dobré to lehoučce rosit rozprašovačem. Já tim natřel po odstrojení elektriky celou frézku a opláchl, musel jsem to udělat 2x, měla asi pět nátěrů. Slezlo vše i včetně kitu až na litinu, ocel, litinu, mosaz ani černění povrchů to nepoškozuje. Hliník se však rychle rozpouští. Hezky to vyčistilo včechny kouty i šrouby. Tak ať se daří.