Hallo Egon, hier wird es etwas schwierig, da fasst alle Farben in Spraydosen Lösemittel enthalte. Ich habe hier mit Spraydose mehrmals in grossen Abstand sehr dünn audgetragen damit das Depron nicht angegriffen wird. Zwischen den Sürühgängen immer sehr gut abtrocknen lassen, je nach Angaben der Abdunstzeit der Beschreibung auf den Spraydose. Viele Farben auf Wasserbasis sind meist ohne Lösemittel , ob aber in Spraydosen erhältlich, hab mich noch nicht schlau gemacht. Oder du beklebst mit Mobelfolie aus dem Beumarkt, geht auch ! viele Grüsse !
Hello, you can use the E205 or a ClarkY. I myself used a HQ from a tall ship as an experiment. The main thing is that it is curved at the top and straight at the bottom - and then the ailerons are curved slightly downwards, which slowly brings flight and a little more lift. Greetings Bernhard
Hallo Bernhard, vielen Dank für Dein tolles Video, das motiviert echt sehr, es Dir nachzumachen und auf den Trottelzug aufzuspringen. Eine Frage hätte ich an Dich: wie gut halten die Scharniere, auch über die Zeit? Ich habe fast alle Materialien zusammen, überlege aber noch, ob anstatt Deiner Glas-Tesa-Klebung Vliesscharniere nötig oder overkill sind. Danke nochmal!
Hallo Butz, ich haber hier ein Gewebeband von Tesa benutzt, lag einfach in meiner Schublade rum und hält bis jetzt noch bombig bei dem geringen Fluggewicht. Der gewöhnliche Klebesteifen geht hier leider nich, hier ist die Haftung zu gering. Aber ist eigentlich egal was man verwendet das Ergebniss zählt im Modellbau😂 Noch ein Tipp, lass dir Zeit beim Bauen und lass die Klebestellen gut trocknen, auch die Klebestellen am Rumpf ein wenig anschleifen hält dann etwas besser. Viel Erfolg !
Hey Bernhard Simml - Can you tell me what is this motor manufacturer, I can just see the KV/rpm speed that it's at 1700rpm/kv if I'm not wrong. Can you or anyone else post a link so I Can see where to order it from/purchase this motor I need few of them same for multiple similar models because the closest I have has long-shaft and it's 3127 at 1550kv FMS Predator made for FMS Zero with 850 wingspan and similar weight as this. Anyone - motor brand/name and speed with purchase link please? Also the appreciation is here ocf. @Bernhard Simml 's eyes only, rest of you can just close your eyes or put FPV glasses and pretend you did not see my appreciation comment and a cry for help in the other hand as I am ready to travel to meet this Thomas Buchwald guy because I got the collection of his plans stored, printed or prepared to be printed in color which is a fortune back in Serbia where I live again now after many years and very happy I continued my hobby turbo-time now with lot of brand new equipment and materials, just sucking knowledge from flug-model and other communities and magazines, websites and yt channels like this is and I hope to have build and finish every model I love and I love 90% of them, coming from Thomas Buchwald lab and working on the plans like surgent but it could be better if the creator can give me few pointers at least or tell me where to pay attention .Not sure if he meant positive brain-hurt or negative brain-damaged by watching it fly so good that it just hurts some parts of his brain :) I would like Thomas Buchwald to contact me via my email at radivojevic.milisav@gmail.com and will repeat it below few times, like I don't mean to impose or spam or be rude, just would like to meet the colleague genius as I help many programmer colleagues for free even if they offer enormous amounts of money to do so, it is not always about the money, you can see/read from the people's feeling how much he loves something and how much he would like to know or learn to do it at least similar way until perfected, so why don't help them if it's just few sentences that can do the trick, stuff or maybe meet a friend or soulmate for life, who knows what future brings to all of us? Mine managed just to pull out some extra endorphins out of it while watching and I have so many questions generally about this build but not sure if I email you do you ever reply to us truly fans of your miracle engineering effort and work of genius Thomas talent - I have spent weeks of trying to find all of your plans, work and dedication to every possible solution you implemented to every model you released via plan at Flug-Modell or YT here and trust me if you are from Serbia and your hobby is RC plane modelling and building them I succeed finding at least 30 of your masterpieces I already spent thousands of euros to buy equipment that you used or at least get something similar to the motor, esc, servo you used on specific model that is by characteristics giving same performance that it gives on the equipment you used to build your models. Trust me even Depron quality in Serbia is a big dick problem, Balsa too so I order most from German eBay sellers or my Serbian friends that work in Berlin or Frankfurt send me every 2 weeks in a mini-wan traveling to Serbia so I Manage to compile some kind of "same equipment you used to build specific model. Working on 2 of them at the moment Buschtrottel and Weisel ( BALSA MODEL) which is pain in the ass to build but I like it because BALSA MODEL IS BALSA AFTER ALL - TRUST ME EVEN BALSA IS ORDERED FROM INDONESIA OR HUNGARY WHICH IS MORE FIRM AND BETTER THATN SHITTZ CHINESE OR INDONESIAN ONE,M CHEAOER FEW EUROS AS WELL WHICH IS AWCKWARD BUT HEY THIAS IUS 2023-RD :) Creator of this pls Thomas, contact me at: radivojevic.milisav@gmail.com Would like to email me for few more things Thomas, hoping to meet you when I come to DE soon to visit 2 friends in "Frankfurt and Berlin if you are close somewhere, just to buy you a beer and have a 5mion talk which will improve my thinking about RC flying of Depron or Foamboard and balsa modeler generally. Let me know if you are available at any chat platform like: Viber, WhatsApp or email and send it to me Thomas at: radivojevic.milisav@gmail.com I would much appreciate those 5min talking to you as I value other people time and will not be boring you with some stupid questions, only the important ones so I don't bash my head against the wall if you already experienced it and know the resolution/answer to that already like I do for many thinks and can exchange them with you anytime. Again, my email to contact me directly mr. Buchwald is: radivojevic.milisav@gmail.com Mickey radivojevic.milisav@gmail.com
Hallo, leider ist der KV -1700 von AirLine nicht mehr lieferbar ( Motor war aus 2019). Aber du kannst im WEB einen anderen wählen (KV 1600-1900) für 2S -LIPO, Gewicht ca. 60g Gruß Bernhard
@@bernhardsimml2505 thank for the fast clarifying reply, you clarified a lot to me just I made a mistake my motor is long-shaft FMS Predator 3128 not 3127 and has 1550kv power which I think is good in this setup. can you confirm one more time pls. so I can start working on this model in few days as I have all the electronics rdy now. Looking forward to send you my result.Also I have Emax GTII series edition 2212 at 1800kv with thrust is 1500gr at 3s batt so My choice is between two of this motors.Any advice is welcome, cheers from Serbia. Mickey PS both motors support 2s and 3s any my choice was 3s GensAcw mini at 2200mah 20c and 2 3s batteries at 1300mah 40c discharge, let me know what you think. Much appreciated on any advise
Hello Mickey, the motor should be at approx. 1500-1900 rpm (Volt x revolution 7.5 x 1800 = 13,500 rpm) and reach approx. 12-15A at 7.5V (Lipo 2S) under full throttle - flying weight approx. 500g . Use the 1800KV, which is very well suited with 2S Lipo, lower weight of the Lipo's and good in terms of speed. With a 2200A Lipo 2S you have a flight time of about 6-8min in normal flight.
Hallo, ....Danke ! Ich spiele privat etwas E- Gitarre und verwende hier eine Loopstation von Digitech. Habe nur in RU-vid 4 sounds von mir veröffentlicht. RU-vid : Loop Bernhard Simml😂 VIELE andere sound liegen noch in der Schublade 😂😂😂
@@bernhardsimml2505 Sie müssen die Schublade öffnen, damit wir Ihre musikalischen Talente genießen können! Du bist gut in Musik! Für mich ist mein Bushtrottel fast fertig, ich musste mir deine Musik 50 mal 17 Minuten anhören, das hat mir Mut gemacht, den Job zu Ende zu bringen. Ich schicke dir den Link, sobald er zu 100% fertig ist. Das Flugzeug wiegt laut Flugschätzung mit RC-Ausstattung 280 Gramm
Thanks and very interesting. Spar now cf tube? Two step KFM. Drawings for the new undercarriage wire? I am building my one now…i tried PVA adhesive but have found hot glue easier to use and sticks better……Laurie.
Heißkleber =>>> Depron verträgt Hitze über ca. 90 Grad nicht besonders gut. Zwar lässt sich Depron in sehr heißem (nicht kochend) Wasser biegen und auch mit dem Heißluft-Föhn erweichen, aber bei zu hoher Temperatur, verglast die Oberfläche und sie schmilzt ein. Heißkleber kann man nur sehr schwer bündig zur Depron -Oberfläche abwischen oder verschleifen . Der Flächenstab ist hier auch frei zu wählen, er soll nur den Flächenbruch vermeiden ! Wichtig ist hier, bei der Vorlage von Herrn Buchwald das Gewicht zu sparen. Ich bin auch etwas über die 430g hinaus geschossen . Aber ... jeder kann für sich selbst seine Hilfsstoffe und Materialien im Modellbau wählen um an das Ziel zu gelangen :-)
Hallo Bernhard vielen dank für das Video. Da ich Anfänger bin im bauen ist dieses Video Perfekt. Da es noch keins in so einem detaillierten Umfang gibt. Wie ich ja schon geschrieben habe bin ich neu im Modellbau und das ist mein zweiter Flieger den ich aus Depron bauen möchte. Was für Ein T Lineal benutzt du denn da ? Bitte mach noch ein Flug Video das Wehre Mega. Gruß Arno
Hallo Arno vielen, vielen Dank dass ich hier etwas unterstützen kann. Bitte beachte, ich habe hier kleine Abweichungen vom original Bauplan vorgenommen. T- Lineal ist eine Aluleiste vom Baumarkt und lass dir Zeit beim Bauen, macht mehr Spaß. Video von Flug Buschtrottel - orange - green - und rainbow kommt evtl. demnächst in einem Stück !?
@@bernhardsimml2505 ist es irgend wie möglich noch ein paar Bilder von deinem Abnehmbaren Tragflächen zu bekommen? Du hast da ja nur ein Stück Holz eingeklebt und die Seitenwände verstärkt?
@@bernhardsimml2505 Hör nicht auf diese Art von Charakter. er darf kein Modellflieger sein. Ich mag deine Videos und das, das 17 Minuten dauert. Ich mag die Musik mit dem Video. Ich baue gerade einen Buschtrottel und du bist der einzige, der daran gedacht hat, ein Video zum Bau zu posten. Es tut mir leid für mein ungefähres "Deutsch", ich bin Franzose... Ich würde Sie einladen, mein Video anzusehen, wenn die Videobearbeitung und der Jungfernflug abgeschlossen sind.👍❤😉
Bonjour, Je suis content d'avoir pu soutenir quelque chose ici. Mais veuillez noter que j'ai fait de petits écarts par rapport au plan d'origine. Prenez votre temps et amusez-vous à construire ! 😃
@@bernhardsimml2505 moi aussi je vais me permettre quelques modifications... je vais tenter de rester en dessous de 250grammes avec un fuselage en 3mm. Le plan est en allemand,je me suis aidé de votre video pour débuter l'assemblage. J'ai appris une nouvelle technique pour la decoration. Ecoutez pas ces incapables, ils sont la pour critiquer. La critique c'est cool mais la critique constructive c'est encore mieux pour vous aider a vous ameliorer si y a besoin. Pour moi la video est bien et la musique est parfaite. La video est sur ma page,j'ai pas fait le montage video. Si vous souhaitez regarder en avant premiere c'est autorisé... la video final sera posté apres le vol inaugural. Je debute le pilotage 3axes,je vais demander a un papy moustachu expérimenté dans un club aero de faire le vol pour que je puisse filmer aisément. J'ai plusieurs projets en cours. Un drone Bayraktar TB2 90cm. NIEUPORT IV 60cm,un biplan F3Ai 80cm "Le Troll"... un mini planeur DLG 60cm prototype... et je vais debuter un nouveau projet pour l'hiver ,le drone Akinci Bayraktar en 150cm. je serais le premier a le construire au monde et je veux construire un avion espion Lockheed U2. A bientot l'ami et bon vol pour tout le monde.👍😉
Il n'est pas facile de tout comprendre en allemand" TRANSLATOR" Mais peu importe le poids du modèle, il vole aussi avec ~500g. Le gauchissement des surfaces à 30-40 degrés est alors important. Vous pouvez donc voler lentement et le modèle est très fluide en vol, même au décollage. J'ai même installé un Profiel E205 par la suite et c'est encore mieux... plus de flottabilité et très bon caractère. En fait je suis pilote de planeur 3-5m, mais je construis aussi quelque chose dans cette classe pour le fun ! Coque en 3mm qui va être serrée au CHRASH, et collante !!
Hallo Bernhard, erst mal danke für das tolle Video. Genau das brauche ich fürs Bauen mit den Jugendlichen👍. Du klebst mit Ponal Express? Ich dachte das funzt mit Depron nicht🤔. Werde ich doch glatt mal ausprobieren.
Oh vielen Dank ! KLEBEFLÄCHEN etwas anschleifen und nimm Express zum kleben , der ist hier gut geeignet und verfärbt sich nicht wie Pur-Kleber😂 Gib hier aber ca. 8-12 Std. TROCKENZEIT - REISSPROBE habe ich nie gemacht 🤔 ...und das freut mich wenn ich hiermit die Jugend auch etwas unterstützen kann !