Any update why noise lifters?

Greatest Troll of the decade 😂

Awesome video. Beats paying 10credits on the OBD11 app. Nice one!

Slow the f down...jeezzzzz

Doesnt it damage the bearings?

Fabulous. Is this the same way in which you can lower the backend too, Just by changing which tooth the arms latch into?? I need to replace both my arms, I want to drop the back end a little too.

What is the ratio of 2t oil : diesel to add? I would like to do i t in my diesel car. I usually put 9liters whenever I fill it up.

Hi mate ordered my fuel line seems like the new one is slightly smaller than the old one is this normal due to heat? Don’t want to replace and something breaks due to it being to small

This is stupid. A single paperclip will save you much time!!

Great for collectors only, not for driving enthusiasts I suspect. Why TF are the crowd still wearing compliance muzzles, it’s a cold you wombats 🙄

I’ve wet sanded my car amazing results

Dzięki wielkie ziomek

2:05 common fault, they rust thru then they leak oil

I can’t even get the wiper off to get at the aluminium ring! Dunno😬

Thanks. Helped a lot.

I've tried to follow your steps on how to do the bushes but I can't get the bars out

Rele za ladenje navoda

Where are the burnt trash go.Does it damage engine somehow.

Going to try this tomorow cheers m8

Spanner size would have been handy, but apart from that very helpful thanks, 👍

Thank you for the video :) I was wondering something. How do we know if it's aligned properly when installing a new one ? There is a third a arrow that indicates it. But i have no idea where it goes.

$300 at a shop or 10 minutes at home.

8 years later it helped me on my car (seat leon 2003 tdi pd) ❤

I’ve been looking for an Audi Q3 heated mirror cap (glass) for a long time. Can you please help me find it or tell me where you bought it from?

Are we able to change hp and torque, or do we need new chip hardware in ecu?

I’ve got a 2000 Audi 13 coup, I’m not sure what size speakers I need, I’ve tried 5,1/4 inch speakers but they’re too large im not sure if I need 5 inch or 4,1/2 inch. Cheers

Any drastic change in mpg?

When I hold the wrench and it says Service it does not stop saying service it just stays the same

I'm gonna get nozzles, a bigger turbo, and a 3 bar MAP sensor, and a tune. My 104hp Caddy will get some gains from that.

Omg. To remove middle switch you have to take pliers grab midle switch in midle and put it out you can use legs if you doing it with no tools to hold it.

Fuel temp sensor and MAF (smoke limiter) on PD cars.

I have a Audi a4 2.0 tdi I will definitely give this a go my Turbo is on the left hand side but hope this will really help think my vanes are sticky I have a EGR delete. And blanked off would I need to unplug the dpf and spray it into the turbo

no wonder they ditched torsion bar suspension. way simpler to just use torsiom beam instead

Hello, i replaced cylinder on skoda octavia, and pedal travel too far. Even pressure bleeding did not help. Problem is air in the cylinder not in abs. Mechanic did not do bench bleeding. So I am thinking to combine pressure bleeding and very slow pedal pressure, what is your opinion. Thank you for answer.

Easy as that 😂

Super easy and well explained.

brilliant video and a very good explained.....thank you

yeah really helpful

Brilliant! This looks exactly like my Skoda Octavia estate. Top tip!

Lol your car broken a-part and you install android on it , glowboxe is almoust gone haha

Seems like you'd gain quite a bit of seat height by doing this, how did they fit?

Can this be the cause of the rear wheels having negative camber?

Do you have a video for the backseat arm rest and cup holder?

Thanks I will try this hopefully I can remove my egr system haven't tried that before. But my limp mode is annoying and no codes

You can try bleeding brakes, then driving on loose gravel and jamming on brakes to operate ABS pump, do that a few times then bleed again!

What is the top light for

Bench bleed?

I have a sticky lifter than sticks for a short time on cold start mostly then clears, I’ve recently changed the oil so it’s pretty fresh but I believe engine has a build up as I dropped the oil a few weeks ago as the filter was bad condition. Which Would you Consider putting in the hydraulic lifter treatment and then drain and new oil. Or flush and drain and new oil. I was considering using the hydraulic lifter for a few mines and then stick some flush in and drain but I don’t think it would be possible if it’s already had the hydraulic lifter treatment in it? Either way I want to put something in it to clean the engine and lifters and drain and then new oil that I will change in the summer

Tenk u men

Nice and clear instructions. Thank you sir. My key is working great again. (A4 B6)