RF, Electronics, Machining, and Other Interesting Things. Basically anything I come across and have time to video. Any RV and camping things I come across. UTV riding, how-to, and builds. CNC Machining from a home setup. Software and DevOps how-to.
Thanks man! I I was wondering if anyone ran into their car not able to move while reversing or moving forward? This is basically what i did: 1. Turn on maintenance mode 2. Replaced rotors and brakepads (push the caliper pin back bc i couldn't put it on new pads). Grease the pads, pins. 3. put everything back on and then maintenance mode. I put my car in Reverse or drive and it wont drive?
Ram just extended the warranty on the seals for the fin and lights on the back. I just had my entire window replaced under this extended warranty, because I explained to them it was a seal issue. That’s what causes the cracks INSIDE the truck on the top of the window frame. Water gets inside and freezes. Check on the extended warranty, because it might be covered now.
hello friend very good your videos!!!! i have a doubt the control is able to resume the machining? for example if i am working and in the middle of the program a tool breaks or there is a power cut... how do i do to restart my program and not start from the beginning, i can start in the line where the power was cut.
You are correct. The way I handled it is manually adjusting the program if I needed to skip ahead with a new run of the program if a tool break occurred to finish the part. Not perfect but manageable.
2017 Passat, same issue on Driver door... my 2012 jetta has 275k miles, never had this issue For the 2017 Volkswagen Passat, the torque specification and bolt size for the door stop are Bolt Size: M8 Triple Square: 8mm Torque Spec: 23 Nm (Newton-meters)
Hello, Are you interested in testing our products? We would like to invite you to test the Scratch-Resistant Windshield for your RZR 1000 (if your car year is 2014-2018
For those who doesn't understand the insides on the box you might want to show a picture or a drawing. I can't see why a gen at 4400w and another at 4000w wouldn't run a small house in rough times or others. Thanks for the posts. Also one might want to add a off switch in the center 8n the wires. Thanis for the posts
I have a 2018 and before I started I put my car into brake maintenance mode. To do this you get in the car while it’s off, press in the accelerator and the e-brake, hold these buttons while you press the start button 3 times. Keep holding them until the brake maintenance light appears on the dash- if you keep the door open you can hear the pistons retracting. I still had to compress but the pistons were retracted so no damage was done. Used a big screwdriver to make space for the new pads.
I don't have it but it was a great machine while I had it. Sold during house move. It was always a solid machine and no issues. Sold around the 300 hour mark.
I got my last Thursday. I love it. It's 7.0 hrs. On it. I'm still getting used to it. I don't a scratch on it. I used to a steer wheel. And the hills? I'm trying to used them. 60in. My wife doesn't like it. I do I'm paying for it
He, estado pegada a cada video, en tiktoc, por eso se que sera un excelente equipo, siempre participo en cada actividad en espera de ser la feliz ganadora. Y esra vez no es la excepción, 🎉🎉🎉, }or eso sigo cada dinámica en espera a ser la feliz ganadora 💖😍🥰🥰😍💖😍🥰💖😍 sería la mejor oportunidad para que la entidad a la que pertenezco pueda disfrutar de un equipo maravilloso.
I just went through a car wash today and noticed a drop of water on the center head rest of my 2020 ram 2500 Laramie, checked amazon but it says the seal wont fit and i really dont want to spend 700$ on a new third break light, also the healiner was wet
Hi guys! please help a newbie! I recently purchased a Fanuc Tape Drill Mate Model T CNC milling machine. I don’t know how to make the X Y axes tied, in offsets only the Z axis? Thank you!
Thank you so much for making this video. I had water dripping from the handle grip exactly as you said. I was preparing to remove the seal around my front drivers side windshield. I ordered the gasket from Amazon. Again, Thank You!
Hi Shane, Love the videos! they have been a huge help. I have a question for you. I have a 1996 Komo VR408, converted to a VR508, router with the Fanuc O-M. It had a static tool changer that was upgraded to an 8 place carousel style tool changer. Long story short, we forgot to change the batteries and lost our parameters. After about 9 hours of manually putting them in by hand, we were back in business... With one exception. The Automatic tool changer. I can do a tool change all day long in MDI mode, but as soon as I go to put it in a program, NOTHING! Any thoughts? Thanks!
@@VickiKunkelI think ita also worth mentioning that I currently have the size smaller to this so the weight will differ. I have the 60 x 30. You may need help. I came here because i think i want a bigger one.
@@ShaneBurrell1 Thanks for the reply. I'm about to inherit one in pretty good shape. I'm pretty sure the batteries are dead, so I'm looking for a point in the right direction for a backup source...
Hi there my KG-UV3D won't clone with CHIRP, gives me a memory read error. I've also tried the actual Wouxun loading software as well. Radio works fine in frequency mode but when i switch to channel or name it won't Kurchunk the repeater. I check all the setting and the offset is all dashes. The menu setting won't let me change it either. I flip back to frequency mode and it works again. I can run it like this and have manually loaded frequencies so it works, I just like seeing what repeater I'm on when flipping channels. Also, curious what hot air gun you use or recommend. Thanks
