Cual era la falla que tenia para cambiar la bobina? Yo tengo uno igual y no quiere encender, y cuando enciende está inestable. El mecanico me recomendó cambiar esa pieza.
Haz pruebas mira ver si tiene algún código escanea , pero puede estar defectuoso y es el que manda electricidad a los coils de las bujías es barato y puede ser una buena reparación de paso como ves es muy fácil , pero debes descartar sino tienes problemas en la bomba de combustible?
Hermano puedes tratar limpiarla con algún producto,pero no te l recomiendo son bien baratas dime si crees que puedes resolverla en la tijenda de autopartes ?
Muy buena idea te garantizo que este producto te va ayudar a limpiarte el sistema DEF , recuerda este es para el Def se echa en el tanque azul ,estás Troca’s del 21 para arriba son muy problemáticas con el sistema de emisiones,buena suerte
Hey bro , yes just side bolts because you need to weld two pieces of metal that comes with the kit or you can do it those two pieces at the bottom are welded to the beam that hold the bumper and connects with the bottom of that Liftgate , the circuit breaker it’s a 150 amp if I’m not mistaken??? I’m not sure now bro because I sold the truck (wich I regret immensely!!!)
Salulo buen video maestro tengo una kia se le cambia la bobina los espare el cam sensor el filtro de linea de gasolina pero estartea pero no prende hay que echale gasolina por el troter prende pero tiembla mucho el motor no acelera se apaga al ecelerar que podra ser si me puede ayudar te voy a agredecer
Kia rio 2002 Le cambié los espares con cables,bobinas ,bomba gasolina y filtro ,corre bien pero de momento falla ,se quiere apagar y no acelera ,,lo apago y vuelvo y lo prendo y corre normal ,,que puede ser ? Gracias
@@CarlosSilva-cm9rnEso lo hacía antes de cambiar las partes? Revisastes las bujias?pon las que lleva original, no cualquier bujía, metele un pomo de limpieza de inyectores completo al tanque ,puede ser los inyectores sucios ,hay que ir descartando
when I had the liftgate installed on the back of my F350 Ford I took the inner screws out of the tail lamps and used Velcro to keep them in place with the outer screws also save me a lot of headaches this is something everyone should think about doing .
Great video! After a good amount of searching I scored a used Tommy Gate and installed it myself the same method as you. Your video doesn’t show the bottom of the gate being connected/ welded to the frame. If you haven’t done so, I highly recommend it as it will flex on the upper brackets under a heavy-ish load. The small bolts can shear causing a serious accident. On my F250, I had a 2” 1/4” tube welded from the bottom of the lift gate to the top of the trailer receiver hitch. Local weld shop provided the tube and welded it up for $50. Turned out great and I now regularly pick up very heavy loads.
Amigo, fíjate que se quebraron los conectores de la bobina, y no se los colores y el orden de como irán conectados en una bobina tengo cable amarillo con verde y amarillo con azul y en la otra bobina tengo igual, en qué posición hirian cada color, el amarillo con verde es positivo y el.amarillo con azul son las señales de la computadora.
2 questions. 1. Did you replace the red plug on the HYD pump with the breather plug? Air needs to be able to get in and out. I have seen the plastic tank on the pump break due to the breath plug not being there. 2. I did not see the mount connection from the lift to the frame of the truck. This is what the plates and angles are for. This is critical! Most of strength of the lift comes from bottom mount. You can destroy your truck bed if you don't have this mount. The truck bed is not design to take the load of the lift by itself.
You got me!!Haha, yes my friend the breather plug comes with your kit and yes I did installed it,second yes those plates are attached at the bottom following manual,I welded them the day after of this video ,unfortunately did not recorded that ,I have to say that was a very great install and the lift it's amazing super strong hold after putting those bottom plates
@@combatvolta Great, I have been installing lifts for a long time and I see people forget them. It gets really ugly, especially after a car accident when they are not there. That lift should give you decades of use
No you just use your own battery,make sure to put a the safety breaker ,normally it comes with it when is new it goes attached to the frame close to the battery
@@combatvolta thank You sir. I am going to purchase a used one two hours away from my house 700 bucks for my scrap metal and junk removal business I make videos for RU-vid I’m going to record all of that as well
@@combatvolta I just got it I am on the way home hour and a half to go 700 it is a little bit rusty but that’s OK if you feel like looking on my page in a few weeks I’m gonna put a video on using it thanks man
Tienes que buscar un bypass pasa en Amazon para que cuando conectes los cables lo adicionas yo tengo otro vídeo que se ven los cables atrás es bien fácil
La cambia y los cables también,,pero todavía me sigue fallando el carro al prenderlo falla y se quiere apagar ,y con el scanner dice ,multiple cylinder misfire que podrá ser gracias
Hi there I need the pcv valve for the very same engine mi tech but the problem is I would like to see what it looks like everyone keeps showing me different type can you please help me
Saludos amigo, quisiera saber a dónde va la conexión que dices que es tierra, o sea el cablecito con el enchufe que trae la bobina.? Resulta que tengo un problema con el mío, ya que la que tiene instalada el vehículo no la tiene y se nota que fue arrancado de allí. Así compré el vehículo y ahora esa pieza me está dando problemas..! Agradezco tu respuesta.!
hola soy de puerto rico tambien, mi problema es que los 2 plugs de abajo estan rotos y estaban desconectados cuando lo compre, ya compre los plugs por ebay pero el color de los cables es diferente y no se que color van en cada lado en tu video se ve bien el del lado izquierdo que es el rojo izq y amar derecha, pero el otro lado son amarillos pero lo que cambia es la franjita una es verde y otra como azul si me puedesayudar en esa te lo voy agradecer bro
Henry Volta ya puse el bypass pero no me deja ver lo que estoy viendo en el teléfono conecte todo el hdmi y los rca pero no me deja ver lo que estoy viendo en el teléfono que tengo que hacer
Auxiliar la conexion esta atras y bluetooth selecciona en el menu de ajustes pariar el dispositivo y active el bluetooth en tu celular y encuentra tu celular
Amigo abajo de eso va una cañería que es la que alimenta la calefacción va al radiador de calefacción y una sale para enfriar la admisión UD sabe si esa va a presión o lleva un hilo
yo hice un bypass mejor porque salia agua dentro la cabina, y era el radiador de calefaccion mejor lo anule, hay que desarmar tablero, y muchas piezas para retirarlo.
Este es con la memoria USB puesta en el cable que está más a bajo por la palanca de cambios.Voy hacer uno usando Bluetooth y Spotify mañana estate conectado gracis