Hello folks, if you came to this channel looking for some fancy hi tlkn fella, well you’re at the wrong channel. But if You’re looking for normal folks living in the country raising a family and making ends meet well you might’ve stumbled on the right place. The Family and I ranch, have a small construction company. And I am a state legislator. The point of this channel is to encourage families throughout the world, and maybe even learn a few things together. In no way shape or form am I an expert on every subject I talk about. But I am open for suggestions. The real point to this channel is to spread the gospel of God‘s love for everyone. We are the light of the world. May the Lord guide and keep you and like always happy trails. Luke
love this! Haha writing a movie and there's a scene where a dad has to pull his son and I didn't know how to do it and now I do! Now i can write the scene! Lol!! Thank You!
Well, I’ve been doing this since I was 14 and I’m 46 now, my father has been doing it since 1978. See the rubber boots give out, they will go bad waiting for the Steel does, and at the end of the day, the rubber boot and the sealant is holding out water and moisture, but the ceiling will last longer than the rubber boot. so at the end of the day, this is a way better option than using a rubber boot, which is still dependent on the sealant. Through the roof last a minimum of 20 years.
I have had 3 ford trucks now with 360/390 enhines. A friend too and they all seem to have an issue with 2 barrel motorcraft carb or aftermarket replacement. Why is it that they start to spit and sputter and act like no fuel or not get fuel when they reach temp, then stall out and wont start for lik an hour? I just dont get it. I keep going through mechanics and noone can seem to fix the damn problem. Replace distributor, coil, fuel pump, ignition module, starter, the square thing inside fender with 4 tabs, everything. It's killing me. Just want to make some damn money already with my dump truck but it wont run good or stay running. I desperately need help. Replaced carb gasket, fixed mouse damaged wires, re-tightened carb bolts, adjust the timing, seriously what is the problem. I even rebuilt a couple carbs, check vacuum leaks, fix them as i find them. They dont all have the round choke piece on the passenger side. Either way its a problem i can get fixed every time.
Honored that you would watch the show. I’ve been off RU-vid for a couple years as far as watching goes. Just started watching again. You know I’m not ever used a sprayer, but I think if I ever did, I would love it. Have you done a video it yet? If not, it would be awesome
I bought one recently and they did change the post to a hook. They do have a stamp on the backside that says to keep it in the safety notch. This can easily be done when replacing the cylinder after loading it. I have tried to remove the metal belt loop but was unable, so they must have improved that. too. However, the buckle thickness is still the same, as is the swiveling trigger bracket.
Not exactly sure what you mean by your comment. I’m sure you don’t find me interesting, but I guess each to their own. You’re welcome for the free video, even though it wasn’t to your liking.
Note that this kind of strainer does not work well for wire that doesn't have knots or barbs. The grips aren't strong enough to hold a straight high tensile wire.
Aren’t you missing a critical step? Isn’t there wiring attached to the switch? How is that removed? And please don’t tell me it’s so easy that you didn’t bother to show it. I own a 73 F350 and I know what a pain it is.
Hey, you’re welcome for the free video. You’re entitled to whatever opinion you so desire friend. If you ever decide to make videos, I’ll just warn you, though there’s a lot of rude, arrogant people out there that are entitled to their opinions and aren’t afraid to share them while they’re hiding behind their own screen with no name attached to their brave & Devenir comments. That was the horn in the pick up you heard friend. You really get bent up over the horn and call somebody a jerk ? I don’t think a lot of people have been punched in the face very much, because if they had, they probably wouldn’t talk is bold as you do .
@@BacktotheBasics101 There was NO reason to have a blaring sound at the start of the video other than to be a jerk. The real problem is that people run around trying to be funny with out thinking what their actions do to others and this world has turned into a bunch of sissys and are unwilling to stand up to the bullies that blare their music or rev their over powered smoke machines. If you are truly interested in helping people, think about how you are presenting your self and how your sound affects are going to be received by some one frustrated with all the brown piles on the internet calming to be factual information. I honestly don't know if you have any good information. The leading silence of the video had me turning up the volume then the noise goes off blasting my ears. If that is not a jurk move, what is it?
@@lostvisitor You know, I read about two sentences of your last comment, and realized, you are easily offended, and probably pretty lonely because of your poor attitude. I hope you’re well, I’m sorry my horn offended you. My advice is get over it.
There is nothing wrong with inexpensive tools, especially if they are not going to be located in a secure manner, in a stationary place. A truck set where the dang thing could just get pitched into a pile of lord know what? Yeha, third hand garage sale tools and chinesium for sure. I bought two rolls, one red, and one yellow to keep my metric and standard stuff handy and color coded.