I want to get this but worried I won’t be able to align the hood without any gaps or anything in it. Did you have any issues with gaps? Or was you able to align everything with the hood pins
All three hood hinges, hood pin on the hood, & Hood pin receivers on the car can all be adjusted. Same as all factory hoods are not square. The trick to hood alignment to gaps all around for me, is very simple, lots of vette owner was able to do it easy. Step 1: Transfer all hardware to new hood, (hinges, some maybe already have pins) Step 2: put the new hood on the car with all hinges and pins screwed on but LOOSE Step 3: Align the hood to your liking, but all fasteners still semi loose, but not moving about, a little tension needed. Step 4: start clicking them in and locking with the correct alignment, 2 people will make this job easier, I did by myself many times, works with 1 person, only because I repeat the process so many times. Step 5 ~10: After alignment, slow tighten down the front hinge to lock in place, in this excerise you will need to do a lot open & close the hood latch, the loose hood pin must be click in everytime, during the alignment, due to the final finish hoods are all in tension and flexed. After start with either side of the hinges, slowly tighten and alignment, 5~10 times, to final tighten of hinges, NOW THE 90% OF THE HOOD is aligned. Step 20: Tighten the pins slowly to factory pin receiver setting, get to as close as possible, then loose the factory pin receiver on the cars and slowly dial the setting in to alignment. Final step: After All Alignment done and pins tighten, you will need sometime later, after 2~3 drives around, give enough time to allow car chassis flex a bit with the new hood, then to go back loose ONLY THE HINGES slightly. THE REASON, is the flex of the car will move the alignment out, the slightly loose the hinges to release all the chassis to hood tension, HOOD HINGES STILL TIGHT ENOUGH TO OPEN AND CLOSE THE HOOD FREELY, while hood pins are holding it in correct alignments. The way, the hinges can settle into the new tension free position, After another 2~3 drives, then go back tighten the HINGES to your liking. This will give you better alignment than your OEM factory hood. Factory installation has the benefits to align hood pins first, then the hood hinges, then actual hood hinges receiver bolt under behind the FRONT BUMPER, to a good FIT. In our case, unless you want to remove all front Bumpers and anything else in front of hidden hood hinge bolts, we are stuck with factory hood hinge bolt settings. Hope this helps, it will take a little while, over time you will get it right,especially 1st time. My to final perfect finish, slow adjusted overtime was just under 1 year to loom like perfect height and gaps. Only due to the 2 pins/2hinges locations coordinating overtime. Thanks for Watching
I would say now after month of Usages and with solar daily charges. I have zero issue running & extracted power into 90% of our electricity uses. I AM JUST WISH I WOULD DONE IT LONG AGO. Of course, this new LiFpo4 battery offers much safer and more life cycles, I am consider lucky to started this year, save money by not owning any less -stable/cycle Cobalt batteries
I have the Delta 2 I didn’t know this mine can use both the Delta 2 and Delta 2 max this is good to know 👍🏽 I need to get the extra battery at some point
excellent Products, I finally got 2 more Max2 batteries for the Max2. It is amazing to link them up to a total 8KW, basically it will power Xbox & 65" Tv combine ~300W, for 26hrs.
Theres 2 different cables xt60 (yellow) and XT60i ( orange) u need the XT60i orange cable they both will work but u will get more out of the XT60i orange cable i have the delta 2 and the river max and both use the same i cable. I learn this thru trial and error
I used this Dewalt Power Station if you got the dewalt batteries, or any Ecoflow power stations, see links below ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-O4xUBjs3AlY.htmlsi=js8CfKpxu-J8-ueD instagram.com/reel/C5HFUTsykpL/?igsh=MzRlODBiNWFlZA==
Amazon Muti battery charger... but, these pink battery suck. I end up bought better one to replace them. The none rechargeable ones. Thanks for watching
Clever idea. However, I’ll just use this idea to color different cartridges from different guns. I have three different CO2 revolvers that use similar round cartridges. Neither will fit in the others’ revolver, so this will help me quickly identify which cartridges will go to which gun.
MJJC is a game changer. I wanna use my 1.1 orifice with the Active 2.0 but I’ve heard you shouldn’t use the 1.1 in the Active bc it puts a lot of strain on the motor and pump. What pressure washer you using?
Sadly the Investor only give OUTPUTS, there is no Inputs, other than Dewalt Batteries. It seems only act as a power station Not a Charger too. Thanks for Watching
I believe there is a second hole with cover to let air in or out next to the pump. It's just about 1/2" diameter hole. Maybe a manual pump hose that size? Not sure if that is what that hole is for.
Youd save a lot if you buy the lifepo4 cells and build them yourself. I got a 100ah 12.8v life cell for 170 bucks. Bought 4 lifepo4 cells and assembled them. Its easy
Yes, you are correct. I have replaced many of mine UPS from lead acid to higher compactly Lifepo4 cells, & lifepo4 power stations. This is video I want to create how I can turn my Dewalt batteries system into portable AC power for daily & backup. In case someone is interested in this for jobsite, camping, or just home uses. As for a full lifepo4 system, I agrees with you, much cheaper that way and combine with solar charging. That is in my list of future projects. Thanks again for Watching!
@Repsol13 sorry if my comment sounded condescending at all. I tinker with stuff all the time man. No harm in that and it's a good idea to be able to turn all those power tool batteries into usable ac power !
Create a distance of the back and try not to block the back panels...bring it away from the wall some and elevate it some...you will capture more solar input ❤
thanks, I also planning on a stand alone setup in the yard below... waiting on the 100ft xt60 12awg extension cable to arrive. That setup should capture more the rear 155Wh panel, only downside is I will need to adjust the panel locations in the yard throughout the day to face the sun. again, thanks for Watching
The key is Solar power... The EcoFlow 220W Bifacial Solar panel is on its way (Fedex), after that arrives. EcoFlow River 2 Pro will charge UP with Solar power under 4hrs. Thanks for Watching!
It is an off brand, not really Dewalt, it is 350W, not other 300W ones. When I said Dewalt Power Station, I mainly meant a power station has all Dewalt 20V XR batteries. . Amazon Link below👇 . 350W Power Inverter for Dewalt 20v 60v Battery, 4-Ports DC 20V to AC 110-120V Battery Inverter with 3 USB-A Port, 1 USB-C Port,300lm LED Light for Outdoors Camping Travel Hunting Emergency(Tool Only) a.co/d/8wEoU1v
for me mainly is the occasion that it applies... not very often I needed full Automatic... makes it pointless as accuracy become more important, thanks for Watching
This is a poorly designed and manufactured air mattress. After less than a month of use, it would deflate even if plugged in. I would not buy this product.
Better to leave it plugged in. I just got my mattress and really like it so far. Its like a real bed. Firm, tall and comfortable. I hope it lasts a long time too!
Thanks for showing the AST2000. EGO's product description says the end is made of rubber but it's not clear from their photos. Your video clearly shows the tip is not hard plastic. I like how the AST2000 is shorter than the non-EGO brand short nozzles on Amazon. I'm going to order an AST2000 as well.