Hi ! thank you for this project, I just completed it but I don't understand, I hear a beep when it turns on then nothing after that, but it seems to me that everything is good, can you help me? (i use Arduino Nano, ATmega328P, BMP180, 3.7 litium,)
If you use this many MOSFETs in parallel, I've read that this can be tricky cause they might not all fire at the same time and only one will do all the work. It would be interesting to see the pulse curve on a scope, to see if how fast current / voltage can come on.
I can appreciate your thoughts on refusing to share information on more powerful devices, however, you're basing the thoughts behind your logic on nasa's "publicly" released research only, and simultaneously implying that differently shaped coils have no magical properties. Now, discounting the idea of magic itself, different coil shapes exist because different outcomes are required in different areas of electronics, so different shapes definitely do have different properties, and you are probably not the authority on shapes and properties, you cannot as an intelligent person discount the possibility that different coil shapes are better for different locations on the body. Or may have other uses not in the PEMF arena. Given that you are one of the few people sharing any information on building devices like this, and that so many people are ripping people off and conning them with expensive coil arrangements, if there is no other information available for making higher gauss systems people with not as much skill as you are going to mess around with it anyway, and likely hurt themselves...Doesn't it make more sense to explain to people HOW high gauss systems work SAFELY, so they don't end up killing themselves? I for one, think a more powerful version may be a good choice to fit under a mattress so that you can use it safely from distances of 8 inches or more. Friend of mine wants to build something like that to fit under a massage table so there is no direct contact with the body at all. Makes sense to me anyway. Zero risk of sweat or anything else making contact directly with any of the coils..
I partially agree with your thoughts, especially the fact that the coil needs to be somehow insulated from direct contact with the body, and it would be best if it were encased in plastic or resin.
@@MirkoPavleskiMK Lots of people aren't fond of resins and plastics in the healing community though. Me too. I work with resin all the time, but enough resin to make a bed...that would cost a fortune. Most people already have a mattress. So, no extra costs. If you put it in resin too, what if it heats up too much? once you build the bed if anything goes wrong inside it you would need to replace the whole thing. I just looked up the price of copper wire, £30 for 1.5 kilo of 2mm magnet wire. Inside a bed of them...thats a lot of money for wire also, which would need to be replaced if anything over heats or...can resin melt? If you have any air trapped in there and it gets hot, wouldn't it explode? Its also really heavy... I would prefer, strong coils 6-8 inches under me. Does 200 gauss..I'm not an electrics person but would that even travel 8"? What is gauss / kiligram force comparison?
You should not expect each stage to double the voltage. From Wikipedia: "The no-load output voltage is twice the peak input voltage multiplied by the number of stages N", not input voltage x 2^N
Is there a minimum coil resistance? I built a 27cm diameter coil with 23 turns of 0.7mm wire and the resistance is only about 0.9 or 1 Ohm. Is this too low?
hi Mirko, what about a device (using arduino or stm32) for electrolysis using alternate waves (so that the water biasing doesn't happen)? Maybe something that can span across a few waves from low frequencies to a few MHz and is able to measure the absorbed current to detect resonance.
I just realized how silly it was to ask about the process, while you're explaining the process, yeez. One more time Thank You for doing this!! I wholly Appreciate you!
From North Dakota, Thank you, Sir. I appreciate your taking the time to showcase and explain the Colloidal Silver making process. I started using a search engine thats not google, Brave, and your video was the second of two videos when I typed "nano-colloidalized". This is a very intriguing, phenomena per se, of processing, channeling energies essentially.. And that Silver isn't the only super electrically conductive non magnetic metal which can be drawn into suspension within the microcosm of the water via, specific frequency of vibration from an anode and diode, right? I learned about this several years ago had no knowledge of it as I can remember prior to then. I looked it up in a 53' Americana Encyclopedia. And I was shocked at the process and production of..And wanted to learn more but couldn't find much else about it in the depths of the google disseminated and undirected me to a nonsensical, unending search query result line up pages, of anything but. A whole lotta stuff, A lot... I'm just grateful to be here, I'm grateful to be able to learn this, so again my friend, Thank You for your efforts. Truly.
Hello again! Thanks for sharing your work! Amazing! I tried it and it works great! I´m wondering if it´s possible to use LCD 2004 directly or is necessary to modify the code? How about LCD 2004 for stereo mode - 2 lines for left channel and 2 for right one? How about LCD 4002? It is possible to use the I2C for any tipe of LCD for this kind of spectrum analizer (I have dificulties because the LCD´s that I have are equivalent, some have no HD44780 and I don´t know the wire conection, no marks - but I have the I2C adapter for them)? Did you tried the I2C connection for this spectrum analizer? Lot of thanks!
