When you do them and flatten them level with the mold leave them set for a few minutes before you push the hop arm down to make the mount section. let them dry for 24h before removing them from the mold. Good luck with them👍🏻
@@alanobrien295 That fella is like my shadow can't move without him, I can't even go bathroom. he sits in the bath and gets me to turn the tap on for him.🤷🏼♂️
@@giorgoslir Thanks. I removed the epoxy and tried something else. I got a thin plastic tube slightly larger width than the ⭕ part on the valve. I cut it size so I can close or open the square ⬛ sections by pushing it in or out if I want to. I got the tube from a water spray bottle. it's on one of the videos.
@@giorgoslir Fast forward to 2:25 I show the valve and explain a little. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-u_tKQsthTb4.htmlfeature=shared
@@sleyddyboby131 Do you mean hold slide release down and shoot it won't lock back 🤔 if that's what you mean it won't lock back if you hold slide release down. If you can do a video showing the issue, upload it to your YT and I can view it.
@@JBAIRSOFTIRELAND I got the problem, its because the thing that you can click on and put the slide back does not have a spring so it just open the slide, but i dont know how to remove or fix it. But thx for the response!
@@sleyddyboby131 it doesn't have a spring to Push that up the little nub bit at the left top side of the mag when all BBs have been fired pushes up the slide lock
I was about to comment "just get rid of that f**** VFC unit" when you did it XD, if its VFC internals it is just crap, absolutly crap internals for the price you are paying for the gun, externals amazing, internals..... And i bet if you swap to a regular bucking you will notice an increase in power aswell. Never worked well for me r-hop, s-hop, flat hop... only with gbbrs and heavy weight ammo, but with AEGs i always obtain better results with regular buckings, guarder, maple leaf or madbull, depending on the barrel and the nozzle length. Maybe you can save that tdc and use it with the E&C unit.
@@fubene5495 No not VFC AEG just the unit is, I have a few of them and all working great with flat hop. the TDC is designed for the VFC unit. I'll get it working I just didn't have the patience for it at the time. I do have a VFC Avalon 4 years old still going good only thing that happened with it was selector ⚙️ cog screw hole stripped.
@@fubene5495 The mcx and vr16 also have issues with gearbox internals gear's smashing bearings fail. the way I look at it, it's pointless paying 400/500 for a AEG just to fix factory mistakes. the only AEG I paid full price for was the VFC Avalon the rest I got on discount 40/50% off
The vfc hop unit is really bad and naturally gives you lower fps. Zci plastic hop units with a 60 degree macron and omega nub gets the best results on a gun shooting 1J
@@simonegan7813 I've tried the ZCI unit with that combo before and it wouldn't seal I tried it with different rubbers barrels nozzles barrel springs hop unit springs different AEGs. Maple leaf rubbers are not good that's why I changed to FPS ones. issue I was having with this, was the barrel wasn't pushed in enough I tried with another VFC unit worked good I have the one with TDC back in with the FPS rubber everything set right getting 1.07j 0.98j with the hop set.
Very good optic except mine i need to tweak with the battery cap otherwise sometimes the dot will not work and it stops working after i switch the light intensity
what is your outerbarrel thread cause i got mine in america so i got a orange tip, when i removed it i found out that the thread was much bigger than 11mm
I don't own this pistol it was in to get power lowered, I just filmed disassembly to help people make it easy for them. if you contact Nov customer service they will can give you info about that. sorry I couldn't help.
I have the version CNC in 2 of my guns and they both work fine. There's no real FPS difference in my cyma sr25 or my double eagle m4. I love in the states and you can't really get the polymer chamber in the states and not paint Taiwan gun the postage to get something that's only $15.
If you look at the ZCI metal unit they are the same as prowin. element. SHS. lancer tactical and other brands, I don't know the OEM but looks like they all come from one manufacturer. Best hop unit I have found that works great VFC. great seal, 0 barrel movement, feed's great fit's in all my guns.
My AAP01 is brand new and I shot it in the winter and it didn’t shoot but then I realized it was because of the cold so then I waited all summer and now it’s summer and it’s 80° out but when I shoot it it jams and stops shooting, I shoot and then the thing that you pull back to reload stops halfway before closing and it’s almost impossible to close. It’s been doing this now even though it’s almost brand new. Any fixes?
Sorry I didn't reply until now I didn't get notification. what I did was remove material from the thee flat sections on bottom of the rear sight, and i done the same on the bottom of the spring guide rod. And a slight dremel on the back bottom section on the inside of ejection port
Just got my aap01 and i have a problem that when you shoot most of the time gun jams and you need to puhs the back of the blow back system to shoot. But some time it just works perfect. When i put some silicone oil inside all the moving parts the aap shoots right for idk one mag and then it has same problem jamming. Maybe it is not called jamming its like the wogle blow back is not making a full cycle and its not loading next bb but when u push it further its shooting. Any sollutions?
If you remove the sight and file the 3 flat section's on the bottom, the middle flat section and the one's ether side of it you don't need to remove loads. And do the same with the underneath of the guide rod flat section that sits on the bolt. so it's the six flat section all together file a little check it file a little check it hopefully that will help the bolt move freely. if BBs don't load remove a tiny little bit ether side of the front feed lips on the mag as they can hold BBs tight. don't touch the top of the feed lips that hold BBs in or BBs will just fly out. hopefully that will help you.
Thanks bro, i maybe do a video for the spanish comunity cos i have the same issues, if it works i will make a video in spanish tagging that one! Thanks i really love that pistol
TBH I don't really know about hpa I'd say the engine will fit but not shure what the trigger would be like and the selector plate as you know are not standard. I think the new APS edge 2 gearbox is standard and they have them with two different types of selector plates the cut out for the selector cogs are designed differently so I think they have the same back cutout as the e-silver edge 2.0 sdu
Please help my aap01 is a day old and brand new but when I go to rack it , it is sticky and the inside of the bolt comes back after the outside and sometimes I have to give the bolt a little push to click it into place once I rack it and it dumps an entire mag of gas without shooting any bbs thoughts?
@@JBAIRSOFTIRELAND hey man thanks for the quick reply, sorry I haven’t been able to get back to you but I just lined it up and used the gun a bit and it that seemed to work😃
@@yurlordnsavior3961 hey man I just lined it every couple days and just use it for a while and it should work and it Dosent work try lubing the sides of the bolt
What do you mean by putting mosfet for the batt? I think about buying it in few days and i wonder if there's any alternative for a starter that's around 300$ or if this specna is a good choice for a starter?
Idk if your able to respond, figured I'd leave this anyway. I have a blowback unit, but when installed, bbs will just roll out instead of shooting as they should. Thoughts?
@@Rugrats_Airsoft is it a lightweight bolt you might need stronger spring is the piston head the original or did you get a new one and change that with new bolt.
@@Rugrats_Airsoft you then probably need a strong spring to have more recoil as it's a lightweight bolt and wouldn't have the same force as the heavy original. you probably need 200% recoil spring.
I used two normal stickers before I read online the ICS sticker works with cyma plat m4's, would have been nice to show that in the manual. It seems to work well now. Not too happy with the programming method but overall not bad. I also had to roll up the cable a bit where it passes into the stock cylinder as the red cable joint made it too thick to fit in the cylinder groove. Edit: I must add Perun customer support is great.
I really hope that you still reply to comments here. I have a problem where my AAP-01 expels all the gas after one pull of the trigger. I have tried two different magazines to see if it was the magazine’s fault but I have the same problem no matter what. Do you know any way for me to fix it?
@@PrestonCornell seen the video could be sight and guide rod squeezing the bolt between the upper and lower. have you tried removing some material from underneath the sight and underneath the guide rod . if you remove the sight and the guide rod underneath you will see 3 flat sections on each part, get a file, dremel, or sandpaper and remove some material from the underneath 3 flat sections on the sight and on the guide rod, start with about ½mm and test it you might need to remove a bit more, but file a bit check it file a bit check it. you also might need to give inside the upper a rub with sandpaper just to remove a slight bit of material and the rounded top section on the guide rod remove a slight bit also.
well i know why its glued/melted. the pin can just fall out. i now have the begadi coming. hopefully I don't need their bucking. I have a mr hop 60. basically a lazy man's r hop.
I think the previous tech tried to fix the hop not staying on, by melting the pin to solve it. Did you order the begadi nozzle or are you sticking with stock one. Maple leaf 🍁 hop rubbers I wouldn't ever again buy or install them on any gun AEG, gbb, bolt action rifle, They don't work that good. FPS softair flat rubber and nub set 👌🏻
heres an anecdote on why you set your hopup. i own a lct rpk16. it shootss 430 ootb but i thought its fine because its a lmg. i have it set to hop .32's and the accuracy at range for a lmg is fairy magic because of the maple leaf bucking and omega nub. its also the perfect setup for .32's i went to a weekend skirmish worried i was going to have a 75 ft med vs my milsim's 50 ft and I was running .28's at 1.7j it was a smaller scale milsim. they chrono'd it on .32's and they said it was only 1.5j so i only have a 50 ft med.
I tested with different parts one by one last two parts was tappet plate and tapped spring even though they looked perfectly fine I changed both and got power back.
@@JBAIRSOFTIRELAND I guess it is because of the proprietary stuff that people do not like them. To much of a hassle and much money to shell out if you upgrade it with non APS parts.
i took apart my sdu and put it all back together but when i put it back together and shot the gun it was a 5 round burst on both semi and full auto anyone know how to fix this?
@@JBAIRSOFTIRELAND i didnt take anything off i just opened it and put it back i changed my mind last second about changing something lmao but i did lose the ball bearings in the fire selector im not sure if that would affect it
@@perks421 Did you remove I.e. lift it up the top with the black strip on the left side, it's just sat in and can come out very easy. Did you put the selector gear's ⚙️ back to normal position way to check is put it into safe is it giving you safe on the trigger. Ball bearing I've lost some if you have any little key chains with the little ball's on or any kitchen utensils with the little chain still attached they use to hang them on racks in shop's Just cut a ball of of it that's what I use.
hi, is your RIS rail also a fraction of a milimeter too narrow? my light mounts that normally fit on any of my other replica keep flying around, and i was wondering if youve seen the same problem with it
I don't run attachment on ris. but I just checked for you it's off spec 21mm instead of 22mm. Way round it cut a strip of plastic card pop it in behind the clamp.
the outer barrel does not move. I tried heating it (in case of screw glue), tried using pliers, tried moving one way then the other. It looks like it's completly stuck, it's insane. I'm quite strong, never had ANYTYTHING resist me when i put my strengh, but this outer barrel did not moved 1 milimeter. Do you have a tip ? do you think puting oil on it can help ?
It's very tight. I done it by hand 💪🏻 I didn't want to scratch it up on the guy. I twisted anticlockwise then clockwise until the glue broke. I'd say get someone to heat it and you try twisting it at same time. Tbh no need for it to be like that it's stupid tight 😡
Hi, i have an issue with it firing full auto when in semi. This issue came after i installed serveal upgrades all at once. Cowcow ss hammer set, ss hammer housing, new trigger, short stroked. Any ideas why it could be shooting full auto? Could i have put a spring in the wrong way when assembling the new hammer set?