thanks for the tutorial. I changed my clickwheel. before screwing everything back together I plugged in the display and turned the camera on. Display is white, I see only an image in the viewfinder. could it be that I damaged my display in the process?? or do I need to put everything back together first?
I designed a geodesic dome with deltoid faces in Fusion 360 before. One before also in solidworks. Now i try Solid Edge and I am really struggling. My issues are how to create an intersecting Point from three Planes, and how I use an Axis for a circular pattern. It took a lot of time, and I still did not find it! I only found how to create intersecting Lines from Surfaces and then I could use the intersecting point of two lines. And regarding the circular pattern, I found that I can draw a circle and then get the bodies along the circle. But this method takes intuitively to much time! So my impression is, that from the very natural logical way of thinking Solid Edge is really not good at all. It is even more expensive.
2005 was something else halo was on the rise 3 was coming and much more in the sequel. 😢 343 really hurt a community i think xbox and halo never comes too mind anymore its finished 😭
I tried doing this but without success. Had an old Asus P6T motherboard, but nothing happens to the chips, not even with the hot air gun at max temperature of 650 degrees centigrade. Only created a big mess. I had success with sulphuric acid based drain cleaner. 30 minutes of heating and only the die was left
Hello! may i ask what are the signs that we should replace the shutter? i want to buy like this second hand but the user said it is taking black pictures...
5:04 man rip Dion Arroyo 20 years later just replayed halo 2 today and saw that and I just feel bad for him and his family at least he'll never be forgotten through halo 2 besides his family if you know what I mean
So what was the verdict after a year did you continue using Solid Edge? I'm on the hunt for a Fusion alternative myself now. Alibre is up there but I do like the synchronous mode in solid edge. Honestly I don't mind a one time fee for a program but refuse to pay an ongoing membership.
Dearest, i can not see clearly how you removed the doorcover of the hdmi/mUSB compartement. My door is broken and needs to be replaced. The door is just 25€, but repair 125€ !!. It can not be that difficult to take the door off, but is not shown on your video. On minute 1.01 it is still on, you remove the cover above the door, and on minute 1.08 it is already off after seeing how you did it ??. Can you tell me how you did that ??
Thank you for your review. Now considering solid edge as I work in mechanical engineering and don't always have an internet connection. Really scared of a program changing its features overnight without options,.
i remember when i first finished halo 2, think i cried because the song was so beautiful. 5-6 year old me finishing halo 2 on easy. by far the best experience that i wish to re-experience again
do you think the sd card slot is accessible even without disassembling the front part? just by taking out the back it should be much more accessible right?
The first minute of Halo 2 End credits made me sad and cry back then cause of my past and everything I done, and hearing the first minute in this video again still makes me think about the past cause idk.
@@mchamster9480 Multi body part. I've been using Sold Edge for 25 years and cringe when I see some one using it in a comparison test who don't know how to "drive" the system.
@@mchamster9480 I would have used a multibody part, with a single sketch profile step including the joggle at the join. Holes added after. I normally use synchronous mode. I don't really understand peoples obsession with constraining sketches in "ordered" mode.
Great video! Please could you tell me where the orientation sensor for the viewfinder is located on theT6i. I have the problem of an upside down viewfinder and the most likely suspect is this sensor. It seems easy to access on some Canon models which is located by the viewfinder hinge, don't think this is the case on the T6i?
I have a problem with my canon d750 upside down screen viewer. Apparently the most likely cause is the orientation sensor which is faulty and needs replacing. Any idea where this sensor is located on the d750 model? There are videos around of the d60 model sensor replacement, which is much easier job because it is location under a small removable panel. Does the d750 require a complete strip down to locate this sensor?
A, why no sound? B, this way you could explain why the actual lens mount is still attached to the camera, which is what I am searching for. You removed the communication pin and their holder. Not what I was looking for but what the title of this silent movie says.
Question for you. Is Autodesk charging you for the cloud simulations, like static stress? There was a good treason for moving it to the cloud. They are now able to implement more robust tools without having to work around the limitations of the OS. That was the reason they moved the simulations to the cloud yet kept one of the simulation types free.
What kind of OS limitations are you referring to? Do simulations use any system dependencies or are self-contained? When I was playing around with fluid dynamics, my only limitation was RAM, which is a non-issue today.
No, it's always about power and control of the product and user, whatever half baked reason the marketing team comes up with to pretend it's not, and "OS limitations" is certainly a half baked excuse.
@@firetruck988 This is what I love about the internet. The developers have had a meeting with me to explain what the limitations were and why they made the change. But someone on the internet gets to declare what the real reason is and doesn’t have any facts or data to back their claims.
Can you describe how the mirrors are placed inside the glass prism (pentamirror)and how it works.. and what kind of mirrors are used... I like the mirror prism (pentamirror)very much. Thanks
Merci beaucoup pour cette vidéo . J'ai une question sur quel site internet on peut se procurer des pièces détachées pour un canon 7 D ? Cordialement Eddy