I bought one and had the same problem, except they put the inside tube on upside down. It looked right but the bolt holes in the bed wouldn't line up. I loosened the outside hose clamp and turned the filler so the holes would line up but it twisted the cheap inner tube so It would not fill. I took the bed off 4 times before I figured out what was going on. 94 Ranger.

اصل کار که جا انداختن تسمه بود و نشون ندادی!! و همینطور روش جا گذاشتن بلبرینگ تسمه سفت کن و نشون ندادی!👎

Nice , u want to do mine ? lol thanks for the video & info .

Thank you!!

What diameter pipe did you use?

Can any one tell me the part # on that little clip that holds the cable in I have lost mine 😢

My 2002 gmc Savana has lost micro amounts of cool for years. It's a 240k miles. I baby it. Barely touch the throttle. Sometime it misfires. Low idle. Vacuum leaks symptoms. Hit a a deer. Installed new radiator. Used a vacuum coolant unit to fill with coolant. It would collapse upper hose for a short time 10 seconds. Then make vacuum in cooling system. No leaks visible anywhere. Heater works well. I think I just need intake gasket, and while I'm in there the spider injection upgrade. What a pain in the ass.

Hola amigo ese tubo va con algún pegamento o así nomás a presión

Good video. Thank you.

Hello sir can you please show me how replace a front bearing please. Your video are helpful alot❤❤❤❤

Rangers must be different, on a old Lincoln that i used to have and on my 91 Mustang, both with AOD's there is no fluid present when replacing the VSS sensor,thank god for that,lol

I think this is what's wrong with mine, but i threw my old filler tube away! I guess I can order a more expensive one.

What a legend

I’m having this problem with my 87 F150. Apparently the hose is pinched by the bracket. Anyone know a fix?

Thank for making this video, I just encountered the same issue when I bought a new one. I switched it out with the older inner pipe and bamn back in business. Good job.

How would you engineer this in with a pump? Just had a HE furnace installed with 3/8" PVC draining to a condensate pump that then feeds a flex line to a utility sink. The pump is too hard to reach to put stone in itself, so looking for a solution before it drains into the sink. Maybe put it just before the sink so it drains downward through stone?

Ford I believe put the smaller hose in those to reduce theft I’ve heard guys say to pull that hose off and gut the filler neck like an old school filler neck🤷🏻

Thank you

Just timing how to setup exactly muck

Great vid.

Looks like bicycle tire tube

Check your OBD2 fuse first,that was what my problem was

10 years later and you're helping me do the water pump on my 1993 Ford Festiva Ed you're a life saver

How you going to change in future?

FANTASTIC , i was stuck with something and you've explained just what i needed THANK YOU .

You don't have to remove the bracket just loosen the clamp and it slides

My story is the same and I believe that I got the same exact replacement part. I am going to do exactly as you have done. well , I just went outside and got the old hose assembly and as you said the inner hose on the old one is far more rigid than the new inner replacement hose is. Thank you for the good information.

Awesome video

I appreciate you posting your video so much! I am a 63 year old woman who needed to replace the speedometer transmitter on my 1989 E350 Ford motorhome, this video was the only one helpful!♥️

For someone like me who has no time or knows anything about this stuff how much money would it be if I take it to a mechanic to fix

Can you say Chinese crap

This what my ,92 ranger needs how do I remove the old one with out dropping the tank

Looks like the pool water test or the salt water aquarium. 🐠🐟🐙

This was 10 yrs ago, very helpfull video for my 323 interplay, I plan to replace waterpump, many thanks

7:03 I threw this spring out of my car and relied on the screw only because I cannot return it due to the lack of space. Does this cause damage to the engine?

7:05 What is the use of this spring?

Thank you. Very helpful.

There not much presser no need for all that .

There no gas gone run out

Thanks for your vid. Just what I needed!

Great video well explained Thank you

Hi bro would you know where the crankshaft sensor is located pld

Hello Mr. Pastore. How many miles and how old was the engine when the lower intake manifold leak started? Where did you purchase your gasket kit, supplies, tools and anything else you used on this job? Thank you for recording this removal and replacement.

Good information, but your voice was not good, missing little information. But thanks for sharing with us.

Thanks !

I own ford laser 1.5 ,year 1991

Great video and instructions

Good

My question, could you just say screw it and take that smaller inner filler tube off and leave just the bigger tube on and have zero issues?

g.m. dexcool coolant eats plastic,silicone,rubber,metal.intake gasket plastic,molded silicone.pressures test coolant system,visual inspection .front or rear intake leaks coolant ,oil