Hi, I purchased the R-SPS3030-232, and the device connects with the software fine. The only issue I have right now is that the real-time voltage and current records only show about 15 minutes of data. After 15 minutes, my old data is overwritten by new data. Could you please let me know if there is a setting I can change to make the software save all the data for a couple of hours of running? Thanks!
this software sucks with the SPPS-S3010-232 when im able to connect without a error its painfully slow. it seems to connect and disconnect all the time. if i press the on/off button 10 times it will only work for 2 or 3 times. if i start the programmed output test it will skip a couple of presets. the connection is just realy unstable but without the software i do realy like this powersupply EDIT: tried it with a RS232->USB cable and its way more stable but still software doesnt play well im only able to ouput a voltage with the "programmed output test" everything else doesnt work.
Please note that the decimal point that can be recognized in the software is ".", while the decimal point in your current system is "," which makes the software unusable. You need to change your system to use "." as the decimal point, so that you can use the software normally.
Здравствуйте, James. Купил я такой же блок питания. Очень не понравились несколько моментов. При заряде аккумуляторов, вентилятор всегда включается на полную мощность каждые 10 минут на 1 минуту. Незавсимо от того, какой ток заряда: 1А или 120mA. Разве так должно быть? А также, вентилятор дует вовнутрь, а не наружу, как показано на рекламных картинках. При этом возникает очень большой шум от воздушного потока, который слышен далеко. Можно ли перевернуть вентилятор, чтобы он дул наружу? Не нарушит ли это охлаждение, так как большой радиатор в виде пластины был заменен на обычный радиатор?
Hello, Olegi. we are old friends. Thank you very much for your suggestions and let me answer them for you. 1. why does the fan always turn on at full power for 1 minute every 10 minutes when charging the battery? -The fans we are currently using are all temperature controlled fans, they will start when the internal temperature reaches 50 degrees Celsius and stop when the temperature drops. 2. 2. The fan is blowing inwards and not outwards as shown in the advertisement picture. -If you remove the fan inside the machine, you will find that our fan is blowing outward, not inward. The reason the airflow is very noisy is because the air speed is too fast, if you slow down the air speed it will reduce the noise, but it will affect the cooling performance. The technology we are using is the latest in all aspects of technology.
@@jameszhangnice-power860 Здравствуйте, James. "If you remove the fan inside the machine, you will find that our fan is blowing outward, not inward." Даже на Вашем видео 0:34 видно, что вентилятор установлен так, что дует вовнутрь. Вентилятор всегда дует в сторону своей неподвижной части на которую наклеена этикетка с характеристиками вентилятора. Можете убедиться в этом на Вашем блоке питания. "The fans we are currently using are all temperature controlled fans, they will start when the internal temperature reaches 50 degrees Celsius and stop when the temperature drops." Я это знаю. Но мне показалось странным, что на протяжении всего времени заряда аккумулятора (несколько часов), вентилятор включался по явно заданному алгоритму: примерно каждые 10-11 минут на 1-1,5 минуты. Независимо от тока заряда: будь то 1А-2А или 150мА.
A minha Power Supply é o modelo SPPS-S3010-232 que não está na lista de modelos. O modelo SPPS-S3010 não permite o funcionamento da função Common Values. O que devo fazer?
1. you can choose SPPS-S3010 model to use in Software. 2. Why you can't use Common Values. Please note that the decimal point that can be recognized in the software is ".", while the decimal point in your current system is "," which makes the software unusable. You need to change your system to use "." as the decimal point, so that you can use the software normally.
Buenas tardes, adquirí el microscopio Yizhan de 24 MP y no consigo que mi pc lo reconozca, tambien descargué Measure, VimicroCam20080819 e ImageView y ninguno reconoce el microscopio, que puedo estar haciendo mal, o que tengo que instalar para que funcione, gracias
you can check our battery type video here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-prElqALSP6A.html Battery Charging Optimization: Our Battery Type DC Power Supply comes with enhanced battery charging capabilities, featuring a protective mechanism that ensures secure charging. The system checks for proper connections, both in terms of polarity and stability, before initiating the charging process. This intelligent design prevents the risk of reverse polarity charging, safeguarding your batteries. Automatic Charge Termination: Once your batteries reach full capacity, the SPPS-C3010C intelligently ceases the charging process automatically, providing optimal care for your battery life.
Hi, I try to control power supply with STM32 via RS232. IS it possible to do it only with Rx,Tx and GND pins? I try to send command from docs, but it doesn't work
Hi, I try to control this power supply with STM32 via RS232. IS it possible to do it only with Rx,Tx and GND pins? I try to send command from docs, but it doesn't work
Кто смотрит. Поясню. Чтобы программа работала правильно нужно на компьютере поставить разделитель целых, десятков и пр. ТОЧКУ. 10.345 (а не 10,345). Тогда программа будет правильно работать.
Your comment saved me. mine the current only showed after 1 amp. After adjusting this setting in Windows 11 I can now see the current from any consumption. thank you very much!
Thank you very much my friend, you saved me. To summarize the problem, you have to change the country to USA in the date, time and number settings to correct it because the application was written in English where the value of one thousand is written as 1,000.00 and in my case in Brazil it is written as 1,000, 00, this generates an error in the program where you are unable to enter voltage and current values through the computer into the source.
Hello, I just bought this power supply and I found that is a liitle bit inconvenient the blinking number when I'm trying to adjust the value. Can you make the blinking slower or to not blink at all when changing the value? Like this one: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3i1560esqY4.html
Thank you very much for your suggestion, I will communicate with our engineers about this issue to confirm whether we can make an update in the future.
I placed an order for this Dual Channel unit but for some reason you sent me just the single channel unit which I am returning , can you please explain why I didn’t receive the correct item ?
Hello, I just bought the KUAIQU SPPS3010D model, this model does not have an RS232/USB Port for using software, is it possible to adapt a USB to use PC software on this model?
Можно. На RU-vid поищите доделку вашего аналога + RS232 порт. Плата уже готовая из КИтая. Только провода перепаять и всё будет работать. Вы тем самым сделаете сами RS232 порт для своего блока питания.
Как долго может работать блок питания при максимальной нагрузке 300W? Проводились ли такие испытания? И объясните пожалуйста алгоритм работы в режиме заряда аккумуляторов: отключение по достигнутому напряжению, по минимальному току, то есть при каких условиях кнопка Battary становится зеленой и что происходит после этого, батарея отключается от питания?
При максимальной нагрузке 300 Вт возможна работа в течение 24 часов. Когда ток зарядки снижается до 0, кнопка батареи становится зеленой, а выход отключается.
12 с лишним тысяч рублей за модель 30V, 10A это - перебор. Тем более, что и без функции "BATTERY", этот блок также заряжает аккумуляторы. Или нет? Также, этот блок любительского класса. Профессиональные мастера, которые занимаются ремонтом за деньги, не купят такой блок питания. А для простого радиолюбителя цена очень большая. Вы раньше давали ссылку на Алибабу, где этот блок продают. Сейчас посмотрел там цену - $67.68. По курсу это - 6222 руб. Почему бы и на Али не продавать по этой цене?
Да, без функции зарядки аккумуляторов это был бы обычный блок питания. Но этот блок питания ориентирован на пользователей, которые регулярно заряжают свои батареи, и эта функция очень удобна для них. Им не нужно беспокоиться о том, что можно перевернуть положительные и отрицательные клеммы и повредить аккумуляторы, и не нужно беспокоиться о том, что процесс зарядки не прекратится, когда аккумуляторы будут полностью заряжены. Им также не нужно беспокоиться о повреждении блока питания, вызванном обратной зарядкой аккумуляторов.
Что касается цен на alibaba, то они указаны для оптовиков, и эти цены не включают доставку. Если вам нужно, вы можете найти меня на alibaba или связаться со мной по whatsapp/wechat: +8619925402565, я предложу вам наиболее выгодную цену.
haha, yes. This model price is good. Price depends on the value of the product. We spend a lot on research and development. This is our patented product, the only one in the world with this feature.
@@jameszhangnice-power860 12 с лишним тысяч рублей за модель 30V, 10A это - перебор. Тем более, что и без функции "BATTERY", этот блок также заряжает аккумуляторы. Или нет? Также, этот блок любительского класса. Профессиональные мастера, которые занимаются ремонтом за деньги, не купят такой блок питания. А для простого радиолюбителя цена очень большая. Вы раньше давали ссылку на Алибабу, где этот блок продают. Сейчас посмотрел там цену - $67.68. По курсу это - 6222 руб. Почему бы и на AE не продавать по этой цене?
I bought two power supplies, they never worked well with the software, I got tired of searching for information, it doesn't work, the voltages jump and I burned 5 fans and I don't connect the notebooks for fear of burning them
@@jameszhangnice-power860 I don't understand what you mean by a tutorial, there are a lot of people and we all have the same problem, respond to customers with solutions if you are in charge of the company.
Effectivement,si les tensions sont du format 5,50V avec la virgule et non 5.50V avec le point,les 10 modules Common Values ne commutent pas sur l'alimentation programmable. Il faut faire la manipulation suivante par le Panneau de Configuration (Horloge et Région) de Windows Sous Windows 10,il faut aller dans Régions/Formats/Paramètres supplémentaires/Nombres/Symbole décimal/ puis mettre un point "." au lieu de la virgule,puis cliquez sur le bouton "Appliquer". Relancer le logiciel DC Power Supply V2.1.4 puis magie: les tensions apparaissent avec un point! Tout fonctionne parfaitement
so sad … it won’t stay on the constant voltage I required … it keep switching to constant current mode … I think this is not supported that feature.. my model is KUAIQU 32v06A model … I want to keep my voltage to 24v and 500ma but it’s not possible … pls help
Note that this is related to the load you are connected to. Voltage and current must follow Ohm's law. As you say, you need 24V 500mA, so are you sure the load you are connecting to must be 48 ohms? Only if the load is 48 ohms, the voltage is 24V and the current is 500mA.
you can connect me on whatsapp: +8619925402565, Email: szkuaiqu@gmail.com . I can ship this dc power supply to you from China. we're DC Power Supply factory.
Проблему вирішено. Вибираємо: панель управління - часы и регион (изменение форматов даты, времени и чисел)-дополнительные параметры - числа (разделитель целой и дробной части:) міняємо кому на крапку.
Effectivement,si les tensions sont du format 5,50V avec la virgule et non 5.50V avec le point,les 10 modules Common Values ne commutent pas sur l'alimentation programmable. Il faut faire la manipulation suivante par le Panneau de Configuration (Horloge et Région) de Windows Sous Windows 10,il faut aller dans Régions/Formats/Paramètres supplémentaires/Nombres/Symbole décimal/ puis mettre un point "." au lieu de la virgule,puis cliquez sur le bouton "Appliquer". Relancer le logiciel DC Power Supply V2.1.4 puis magie: les tensions apparaissent avec un point! Tout fonctionne parfaitement