Love the outdoors.love bushcraft but can't afford the expensive equipment so all my stuff is from either ebay, amazon, or from car boots. Also Walks and cooking a steak and burger in the woods. Do all own repairs to house and car so may put them on video if any interest. I'm a class 2 driver on bin wagons at the moment.
Hi ,if I understand correctly this kit is used internally after removal of skirting and old plaster . I would be interested to hear what others think. Thanks
waste of time this, sorry to say but these treatments are sales man’s wet dream. You should already have a damp course on your cavity wall house. may be it’s below the concrete path and it’s being bridged, never butt concrete up to the house. High ground level, bad gutters, blocker backing up drains and leaking underground water supplies are the things to look for. Prevention is better than cure. Cavity could also be full of crap, so a few bricks out and clear the cavity.
Hi mate Thanks for sharing video. Can you please tell me if it sorted out the rising damp. I have a similar problem and wonder if this is a good solution. Cheers
Hi I've watched this video very educational thanks, i can't find the other one showing the job once completed the one you said you was going to do next.
Used these , three months on, the rods look just the same, the mortar in my wall is still reading 33% on my meter, ( and this is in the summer months ) which is the maximum it will go to. I think I have been conned, big time. Thank god I only did a 10 foot interior wall, as a test before doing the whole house.
You dont use them with a trangia. you put ethanol or alcohol blocks in the bowl reservior and control the flame with the sliding lever. They are used in restarents, bars, cafes, hotels all over the world. And are rightly considered the best stoves out there now the Origos boat/tent/ice fishing heaters are dead with a heater attachment. With a stainless steel gas camping cooker heat exchanger add on you can use them as a safe hot tent or van heater as they give off CO2 rather than CO. As these are now about £8 to £15 on Ali and are going for up to a mad £40+ on some UK catering sites you have a bargain.
My friend, CO2 is the sign of carbon dioxide, it can cause death in a closed space, but also in a tent without ventilation! Ventilation must be ensured when using the device.
@@amateurlifers9797 my sheet says your code says open circuit or pump failure. Im not sure all these codes are for everyone or not. Mines a 5kw portable in red
@@greasedmonkey7571 hi been on the facebook cdh sites, they were saying it's the battery, so I've bought a adapter to go from 240v to 12v, even though the new all in one cdh works on battery, so next is to try and get it working on that will let you know. As for the pump, its definitely pumping/priming the fuel to the cdh, but when i press start nothing happens lol.
Thanks for video I'm planning to do soon much appreciated with instruction not sure if I still need to take plaster off from inside to do the same or will be enough to do it from out side how was the affect did this product did well ?? thanks you so much
I'd maybe look for other sources damp, ie condensation. Raised external ground levels. Blocked drains/broken drains. Inadequate rainwater disposal. Blocked or missing sub floor air vents. Modern plastic paints. Cement renders. Gypsum plastic. ..... to name a few
Hi all I plan on doing a follow up video next month (time off at work lol) on how it has worked, I will be showing why I did it this way and what some comments have been like good and bad. And what if any my plans are next. THIS IS NOT A HOW TO, OR SPONSORED VIDEO, AS MOST OF YOU CAN TELL IT'S AN AMATEUR VIDEO ( SOME CAN'T TRUST ME LOL) Sorry for shouting but some need to get it through to their brains, that I am trying to stop damp in my house and I have never done anything like this before. Thanks for reading my bit of a rant see you in December.
Is this recommended if I have issue in box room upstairs. Also hiw do I gauge where to drill if my outside walls are rendered a d cannot see mortar lines
I was thinking of having a go with this myself as i had loads of damp walls in my bungalow, however as it needed treated from the inside, there was loads of plastering etc so i got a company in to do it. I had a few good convos with the guys doing it, one thing they did tell me....if the damp on your walls inside the home is above 1 meter, then chances are its not rising damp, as the weight of the water rising against gravity does not travel higher than 1 meter. I had 8 internal walls treated, that was the plaster taken off to 1 meter, the injection damp proof, and then a membrane along the wall followed by new boards and plaster. They also told me that the injection / rods were only around 30% effective in their experience, and really its the membrane on the walls that stops anything coming back through. Not that I have a clue about damp, just thought i'd relay the information in case it can help someone. Anyway, great video mate, very helpful to anyone thinking of having a go.
I think it has worked, the damp seems to have gone, in the bedroom above and kitchen wall also, the walls feel warmer and the next thing to do is the plaster on the wall. I think the main test will be this winter to see if the barrier of damp proof is still there. We've had a lot of sun on it so the wall should be completely dry now so this winter I'll have to give it a check to make sure. Thanks for the comment 👍
Grate job. Also would like to see any diffence over this winter as no videos on RU-vid after when dry rods been installed. I guess you will have another 17K views. 👍👍👍😉
Similar to the X stand you have is the Toaks 6 plate version. File V notches in the top of the burner holder to register the X pieces more positively. There is a good vidio on RU-vid showing a conversion to make the Mini (28) into the same format as the 27 & 25, which I shall attempt later. Thanks for sharing Take care
Hi, yes had a big drop in the coldness of the wall especially in the bedroom above, was getting lots of damp in there but now it's almost gone. It was quite easy to do it after all the measurements where done, glad I used the tape to mark it up beforehand. Hope it goes well for you. Thanks Adam.
