As far as 'hopping' when you get on, I discovered that if I step up with my right foot on the step, then my left foot is on the platform and easier to turn/sit down.
Does it shake a lot, a lot of vibration? That's the thing i don't like about mini bikes. But since b200rsv has front and rear suspension that might be a game changer.
Make sure you are going with a low-pressure nozzle or no nozzle to get the soap dispenser to work. I would keep reusing the clr, til it starts working properly again
Have you ever had any issue getting it to start ? New to mini bikes myself & not sure what to check for it would only run with the choke then wouldn’t start at all tried cleaning the carburetor can’t get the housing off
it's like any other small engine. choke on, let it warm a little, maybe a touch of throttle, choke off. could be flooded with all that choke? check spark plug? haven't had that issue with mine. always starts right up with the correct choke process. bummer for you, good luck. i'd imagine these cheap chinese engines could have lemons. return /replace it if it's new and you can't get it to work.
I have a brand new one with same problem. Could CLR fix it. When I press the trigger there is a one second hard discharge then very weak. What else could it be?
are you holding the trigger down for an extended period of time? this would allow for the system to be primed and all the air pushed out. you need good water flow and no air in the system. trying running the hose until the air is out them connect it to the pressure washer and try, could have a lot less issues. sorry if that wasn't your problem.
The thing on the exhaust tip is to cool the exhaust and protect from burns when in regen mode. You'll notice the tractors that don't have Diesel Particulate Filter (<25HP)have a regular exhaust tip.
I loaned mine out… big mistake. The air intake cover itself was full of feathers when it was returned, but I didn’t know until I went to use it weeks later. I cleaned it out, the motor will hum, but not turn. Any ideas how I can repair it? The motor cost as much as a new machine. 😢
bummer, hard to say. wonder if it got all wet and rusted together. maybe try hammer tapping any spinning parts that may have rusted. free turn the drum wheel. just guessing here.
if you move it around on grass, they always just pick a corner. if you drop in some straw/hay and leave it place for a while they'll all share a nest they make.
I like how the culprit's face was shaded out, just like in a murder video -- it is a murder video! But I fully understand they have to pay for their sins.
Thank You!!! I have same model -- just tried your recommendation and it works. For others: don't give up... I had to add more CLR to the soap dispenser and continue to run the washer. After about 3 to 5 minutes, it started spitting and eventually back to the strong power wash.
Will try your method again. P.S. I just add it in the water garden hose port (water go in) and seal the other side with balloon, and let it sit overnight, and it did not work.
I have the same problem on the same model and I worked the same way , but didn’t solve my problem and still has no pressure . Is there any other solution?
I’m looking at one now for a friend, same symptom Wondering if I should pull the pump and check the springs and check valves I took one apart years ago and vaguely recall small springs and nylon discs/ plungers They may all be oxidized with hard water and siezed up CLR is worth a try along with 60 # h2o # behind it later on
No its not worth it. Tractor is light and will easily tip over. Too narrow even on flat ground. Accessories are so over-priced. I should have bought a used tractor with loader.
everything is "overpriced" blame the government. almost every tractor is tippy with no counter weights. most tractors are too narrow and people add spacers. used tractors still cost a ton unless they're old and broken with tons of hours.
I have same bike no rear suspension and ur right its a big solid minibike u dont want goin faster than 30... i got mine to 43mph stock engine did a little govenor adjustment and popped off all the throttle restrictions thats fast enough
The new plug worked for us for one season, then the plucker crapped out again. Tried replacing the capacitor but so far no luck. We have 36 chickens to process next week and probably going to hand-pluck😩
Also, I have another question. You showed those larger rounds that you cut, and mentioned that is the biggest you'd want to cut with the saw. Do you think the 14" bar version would perform similarly for that size cut? Thanks!!
Probably, that won't have much impact on the power just size of bar. It's still the same motor and source and both those bars are larger than the cut in question.
I'm not sure, a good bit but definitely not that long. The saw just isn't really meant for that. I just went and bought a new 24" 60cc gas saw for big jobs to replace the old gas one. This is for trimming and convenience imo.
This is actually pretty cool and will make having geese way more enjoyable. It ticks off all of the things that are important to me like ventilation, easy cleaning, nighttime protection, easy to move/lightweight.
I want one of these.I had the money for like a week ago and I end up purchasing something else and tell after my trip to see my kids.Just in case I fell off the d*** thing, I wouldn't ruin the trip.But I will still get one of tyes
I got a crapsman D.L.S limited edition what ever right the thing is they put a plastic round cap built in to the seat witch doesn't work very good they just keep making stuff crappy an comitcadit
everything is made like crap and as cheap as can be these days in the consumer categories, sadly. gotta spend some serious money to get quality now or stick with old stuff.