I did try filming a couple of extras that I have with tx, they do sound fuller and louder. totally agree! hahaha haven’t try it with deskeys though. what did you filmed it with?
@@Kw1spyboards i filmed them with 0.3mm poron films which should be similar to Deskeys. I also spring swapped to a 20mm long spring but i don't think a long spring is it for the snow rabbits as it feels a bit too "tight". What are your thoughts of the default spring?
@nocopyrightvideo402 well that’s interesting. I haven’t try it with a 20mm springs. I actually like the stock spring. Cause my sweet spot is around 55-58g. Too bad the stock spring came unlubed. It would’ve been nice if it came lubed from the factory.
@@Kw1spyboards i actually revisited my snow rabbits after this conversation. They do sound different with the long springs. I prefer the sound with the short springs. The long springs kinda make them sound thinner and drier.
Especially the spacebar, sometimes it sounded too much like a porcelain, i feel like for dcs when it hits with a build, it hits hard, otherwise gmk still wins, but dcs w browns is 🔥
totally agree with you there, I might need to try them with mx browns now. I tempted hahaha. I still prefer gmk overall as well. but It’s nice using dcs just for the sake of something different.
my stock ones are quite scratchy and low in volume, i think that i might need to lube them, do you recommend filming them or do you think that the tolerance is a bit too tight?
hey rassles! yea I did the same to mine. I end up wiping out all the prelube and retuning it with thin coat of 205. It does sound louder. If you are using TX 0.125, you’ll be fine. More than that it does feel too tight.
Maan, watching this vids for several times, and loved it so much. ❤ Its just so nice with the sounds, the keycaps, the config. Made me end up buying 1. Lol. Lovely vid!
om antara mx black, gat x, oil king, mx purple paling suka yg mana di alas ? kalo gatraw d alas menurut om gmn ? dari beberapa video, kayanya scratchynya mx purple paling menarik
cuman kalo harus milih option di atas milihnya mx purple sama gat x sih. mx purple itu lebih ke fun build imo. cuman dipakein mx brown jg resultnya bakal sama. kalau pake gat raw juga bagus kok, tapi bakal kekencengan. kalau sukanya gitu juga ga masalah sih wkwkwk
@@Kw1spyboards nahkan purple dan gat x haha. liat di alexotos last build jg pake purple, kayanya terinspirasi dr si om wkwk. kalo plate mending alu bawaan, apa cf ya om, swittch gat x r2 aja nih. makasih banyak udah reply om
alu bawaan aja uda lebih dri cukup imo. alas pake cf plate blm pernah coba sih. itu keknya alexotos build duluan kok kalo gk salah streamny. ini juga pake mx purple karena req client aja, pake mx brown juga oke resultnya. sippp sama2 om semoga ngebantu. kalo ad further question chat gw aja di discord
Damn, that was gonna be my exact set up too, but I think I will go with some silent switches over my usual azure dragons because I need to use it in the office
I just do some light coat of 205 on all the stem plus the bottom housing railings. oh and I didn’t lube the stem legs, since the client want that tactile scratch feeling of cherry tactiles
@byake I didn’t clean it cause the prelube is only outer portion of the holes on the bottom housing, like the prelube is just so that the spring doesn’t pings. as long as It doesn’t get to the bottom housing holes or side rails. You’re pretty much fine.
👀👍! imo i feel like the snow rabbits dont sound as full when compared to nk creams. then again, it could just be the recording and my headphones, but side by side comparison would be nice.
yeah you’re right. I was actually planning a comparison, cause previously the KFE CE was built with NK Creams as well. But then I realize that old vid has a different recording format from this one. So I’m not sure if It’s good enough to be use as a comparison. too bad though.
Definitely has the timbre of kailh creams, but just a bit drier? If that makes any sense. But probably just due to differences in handlubing kailh creams vs prelube gateron.
Listened at first, said "switches aren't lubed". Checked description and what do you know? I'm getting better at identifying these things 😭. Also nice video. Clackity clack clack.
oh what I meant by “I didn’t do the switches” is someone else lubed it not me hahaha my bad. Should’ve been more specific about it 😂. Thanks for the compliment btw hahhaha
It’s not mine. It’s the Acid&Co’s owner board. Also the board is a special unit for vendors, that’s why the engraving is different than the others hahaha
Glad someone brings up the softness for top mount in numpad area. i ended up gasket mount the numpad because it wobble so much. maybe it would not be an issue if using harder plate material like alu
yeah that kinda annoys me a little. but in normal use the softness isn’t that bad in alu plate. as long I don’t press it super hard. but yeah I was considering using gaskets only on the numpad but I’m worried with the difference in sound. Glad someone noticed it as well hahahaha.