Our channel incorporates a variety of informational product videos, customer testimonials, staff spotlights, and more.
For over 60 years, the Flaman name has become synonymous with quality products, reasonable prices, and outstanding customer service. Through steady expansion and innovation, the company has transformed from a rural-based reseller of grain bins that operated off of the family homestead, to a Western Canadian retail powerhouse, with locations across the prairies, a vast and diversified product line, and an ever-growing base of loyal and valued customers.
Hola. Me interesaría un proyecto de secamiento para arroz y que funcione con cascarilla de arroz me encuentro en Colombia cómo puedo obtener más información?
Just bought a 2024 Trailtech trailer and had to rewire the whole trailer. I was afraid I would lose my lights and brakes hauling my tractor. My 20 footer came with 2 inch stake pockets. Good luck locating any accessories to put in those stake pockets. I guess its my fault for not having a tape measure at time of purchase.
Just bought a 2024 20 foot flatbed with 2 foot dove tail. This company needs to fire all the electricians or send them to electrical 101. This trailer had the worst wiring I have ever seen. I ripped all the wiring out and rewired. I took pictures and video of there fine wiring. I was afraid of loosing my brakes and lights. All grounds to trailer frame were wire wrapped around a screw. Hopefully the rest of the trailer will be wonderfull.
Just bought one 2024 , 20 foot flat bed with 2 foot dove tail. The electrical wiring was the worst wiring I have ever seen. I ripped out all the wiring and rewired everything. I did not want to loose brakes nor lights at night. I have pictures of the fine wiring done. The trailer is useless without brakes and lights. The electricians need schooling 101.
The wheel wells are junk and every one I have seen around town has the wheel wells sagging. It then creates cracks everywhere at the end corners and center of the diamond plate as the saggy metal flops up and down as you drive. I had to weld all the cracks and added a 1x1 square tube center support off the shackle/hanger mount up to a plate welded to the bottom of the wheel well, then it was 100% fixed for a year so far. In the end if they are going to keep using less than 1/8th" wheel wells they need to add center supports. Oh, the ramps barely hold an 8k lb excavator, I plan to add tubing on the underside of the ramps where the edges are bent under like c channel. Those bent under edges flared out so I had to use a sledge hammer to bend the "c channel they formed" back under it straight so it wasn't too wide and would fit in the ramp slide-in mounts. The ramps are straight and not sagging but they flared out at least 1/2". Luckily I have only had to rent an excavator 3 times. The light in the box is great, charging outlet is great, the front box hydraulic the holds the door open died in a year. Otherwise it's been great, the supports are fine I have dumped hundreds of loads of dirt, mulch, gravel, trash, etc. The floornis so thick I have even scraped mud out of the bed with my flat blade tractor backhoe and made no dents like othe trailers have the valleys. Oh, also I keep a can of rusteum high end universal black paint in the box and spray scratches all around every month or so. The rubber tube covers eventually pop out a little so I used quad siding cualking to glue them in but also its soft enough to pull out the caps if I ever need to. I have lost only one cal now. No issues with the lights! Herculese tires would have been better than china bombs as two have blown and I have started upgrading them to G or H rated(can't remember) Hercules. I would buy it again, but have the well supports added right away and see if the dealership would have added legit tires as a upgrade.
Drop axles with slipper springs will give longer life than Tortion axles ! The hard rubber inserts on tortion axles will wear OUT because they're constantly being flexed so they lose their resistance to inhibit wheel flex over time !
I bought a used 07 F550 with a CM bed I need a 5th wheel hitch not a goose neck the goose neck is not removable. I want to add a Curt 30K 5th wheel set up any suggestions what I need.
I upgraded to a XH1500S5 from a FX1800, it’s a HUGE upgrade and aside from everything mentioned I love the wing gauge wheels. With my FX1800, if I traversed across gravel roads running through my fields, sometimes the skids would catch on the side of the road…the gauge wheels prevent this. The one thing that I’m not a fan of is the 5” blades. I ordered my FX1800 with those blades and no dealer anywhere stocks them. They all have the 4” but not 5”, and for a while my dealer couldn’t get them because Schulte didn’t have them.
