Hi where did you get the charger from

আপনার কাছে থাকলে। বলবেন আমি নিতে চাই।

ماذا تفعل عزيزي ليس بهذه الطريقة يتم التعامل مع بطارية الوثيوم ولوحة البطارية تحتاج لجهاز فك الحام وليس كما تقوم بشد البطارية

Bisu

On the 1KZTE built in 2005 the pinout for self diagnosis is 4 and 13.

Not very informative

Hallo ,ich hab die gleiche leider drei eine reife Leuft langsam dann nach par Sekunden geht aus

Te lo compro

Hmm, what happened with the steel 'half'ring in the front ? As I can see you didn't replace it again.

I get it into start

Nice, but the problem is how to find spare parts. It is almost impossible in some areas. And if you find any part with no numbers on it you will have to buy a new PSU.

Cool battery fix. that sound is the roller brush. The bearing cup opposite of the drive end is worn. Hot glue fixes that right away.

Hi denis, hier ist Max aus der Schule, hast du Instagram?

Same issue, wire snapped off the coil at the connector. Ended up positioning it near the connector and then dumping hot solder in the gap to bridge it. Works again. Thanks for posting!

😅 Promo-SM

That is exactly how I got my 3000 working again.

Goedemorgen ik heb een toyota opa en start niet. 2 keer nr de monteur gebracht alleen uitgeven,juist erger geworden. Eerder door te lang rijden gt de motor dan uit, dus kan nt vere afstanden mt de auto. Naar de monteur gebracht kan nu nieteens meer starten. Nieuwe sparpluk, battery, beld etc.😢

My Siemens device gives the message "Door is open", when it is not and no door is open. Also, by turning the device off and on, the message remains and the device has no function. What do you think this sign is? Thanks

What is the name of this replacement part ? Is that pump part?

great job you make this stuff look so easy!

How long did it last

Ahhhhh ohhhh hahahahahweeeee-ohshit

Can it detect gold

hello i have the some problem to... but that solution is not working..... what can i do？

Halfway done with mine. Just now found this video. I wish I would have found it sooner. I hope I don’t find that I screwed something up. I’ve been just reading the screen printing on the board and using a multi meter to read the components and I’ve been hoping I’ve been putting them in the correct spots. This video should make things much more clear and a lot easier. Thanks for posting

Please short the Electrolytic capacitor thy bite

Where to buy battery for this same unit?

7 batteries why put 6?

Thank you so much for this tutorial, I can repair my phone with success !

Useless...

Are the voltages marked on the board?

Waaaaaaay too complicated for me! Buy another!

Thank you for this teardown! Thankfully I didn't have to replace the back speaker. I cleaned the pins with some alcohol and now it works perfectly.

❤🎉

Yes, good calcs, but please...staple your resistors together like pages of a book, in order, and you'll find what you need in 2 seconds.

What is the name of that transformer and what is the value of it?

I am using a potentiometer to control and slow down the speed of the 555 and the LM4017 outputs. I'm wanting the LED's to fade when they come on and off and I am experienced with many different circuits that fade LED's. I have tried basic cap and resistor pairings at the LED's and also by using the 4017 outputs to drive bc547's transistors that turn on the LED's, again with different arrangements of caps and resistors on the base and/or emitter sides and I've also tried resistor/cap arrangements that can turn square waves triangle or sine, with and without the transistors. In all cases, I can get a very controllable fade out of the LED's but cannot get them to fade on. Is there something about the output of an LM4017 that will not allow it's waveform to change or for a capacitor to slowly charge? Or something else that I just can't figure out?

' no hear sound alarm while metal detector turn on

Not sure why you're afraid to talk us through this process and what you're using.

There were 2 LEDs missing in my package..😢

Please explain more.

Power doesn't not turned on for somedays and again it turns on after somedays. Anybody ever face this same problem? Please help..

Wait can you explain why it stopped making a short... What did you move i couldn't see

Dogog❤non no❤plugsnospsrk no start ❤

Making use of the ru-vid.comUgkxcJ22tnHH9l1vjdIdEIG27iOG55P7LXI8 reconditioning plan, I just saved 2 auto batteries from being completely junked. The guides were very simple to follow. I wish I would have found this years ago! You may use the guide to recondition any battery type

❤✌👋🌹🍀

ممتاز فلك الشكر سلفا

Mine is flicking at the start every time, is it the same problem?

Hi, I have an EQ5 macchiato plus, it doesn't make coffee, it takes the coffee beans and grinds them, no coffee comes out of the machine. The coffee grounds are hot, it can lower hot water without a problem, has run the self-cleaning program several times but without success. What could be the reason for this? Thanks for the help.

I bought a 3000 years ago and until today I worked flawlessly. Of course the thermal fuse decided today was the day it finally just said “fuck it” and gave out. Luckily we can buy spare parts for a tool that costs less than $90 though. 🤣