I’m using a star screw driver to try and program and ET one button remote to an ET500 gate. I’m pushing the star screwdriver against the BT section (centre of the 2) but I’m still struggling to get the remote to link. Help please
This video was so helpful. I managed to close the garage door completely. It was very frustrating during windy days as it would blow in the leaves. And shaking the door constantly.
Thank you for the comment, so you have a bigger issue then just not completing the limit setup, what was the reason for wanting to reset the limits? I would look at the actual gate, wheels and guide roller, it not moving at all means a jam or obstruction at high output, could also be a dead spot on the electric motor
@@nicksandtrickssa The reason for resetting is because it is a second hand motor that was bought from someone else and the limits are not working right.The gate is moving freely and I did check the wheels and stuff.It starts the setup but as soon as the magnet gets to the sensor it stops.
@Monyadiwa thank you for the comment, if you have an aluminum door and it only works when the door is open or even half open, then your door is blocking the signal, you can install a weatherproof receiver on the outside of the garage, but it requires you to run a cable to the receiver
Lastly,i have 1 remote which was working together with the one on the wall but after i did some toughing to the buttons trying to program second remote,all the remotes are no longer working. Can you maybe assist what could be the problem?
Thank you for the comment, apologies for the late response, a E1 error is PC board related, you have to take it have it repaired at your nearest reseller or get a installer to take it in for repair
@abiedahsonday3187 thank you for the comment, please see ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-0IK7CKwFOio.html an updated video for the audio problem, what do you need assistance with?
Thank you for the comment. If you have all the remotes that's left, master erase the receiver and program what you have still ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-b6h0_9kLisU.html
@@jonathanprince2667 thank you for the comment, but I have made an updated video, ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-0IK7CKwFOio.html Addressing this issue, hope it helps
Thank you for the comment, it's the easiest way of making the button stop working, but it does not erase the button, just changing the remote set from ET blue to ET blue mix, but great if your remote is on someone else's motor
I see, my remote wasn't working so thought it got deleted, so I held in the button till it flashed then it worked again. Any idea what this function is for?
Hi there, i have a DC Blue digital version 2( green board), all of a sudden when i press the remote, there is a clicking sound from the board and LED 4 lights up, when i press the remote again, another clicking sound and LED 4 goes off. cant seem to find the issue. any suggestions or advice?
@@NaweedMohamed16 thank you for the comment, sound like a faulty PCB, stuck relay mb. If you have a wooden door then your inner motor could be done as well
I think my dc blue advanced pro stopped working. When I followed your guidance to left, It gaves me E1 error and it continuously beeping. Should I get someone to fix it for me? thanks.
Hi great video however I'm struggling with my gate motor, it all of a sudden stopped working and would close but only open half way, tried to reset the limits but it closes and starts beeping 20 times what does that mean? No light are flashing and when i open it the LO light is on but when i close there is no light
@@rsaboertjie2109 thank you for the comment, it's seeing a collision midway, if the load pod is turned all the way clockwise then focus on the gate itself
Hi. I have programmed 2X Nova remotes and added 2x more afterwards which all work fine. Problem now is that I cannot get the motor to program new remotes or delete buttons. I get 3 flashing when trying to program. Two of the remotes "decided" afterward to open the garage door and gate when pressing the gate button and am unable to delete or reprogram. Any ideas. Thanks
Thank you for the comment, 3 means no transmitions received, either the remote is too old or not on the correct settings, press and hold your ET remote button until it pulses slowly then try again
Thank you for the informative video. I used it to set up my door, but I'm experiencing a different issue now. Every time I open the door, it stops halfway, and I have to close it before trying again. When I try opening it a second time, it works. Do you know what might be causing this?
@@cebongcai740thank you for the comment, it could be the door is not weighted correctly, or just the weather making the door act up, change the F, force, setting for now and set it back when the weather gets better
Thank you for this video 🙏🏻 has helped me a lot with programming my remotes as well as working with the motor. I have a question that I’m hoping you can help me with. My garage door is closing and then sometimes 1/2 or 3/4 way down it stops closing, beeps once and then opens again. If I stop it opening and close it again quick enough it will close fully. How can I fix this?
@@oldboneybird thank you for the comment, it sounds like there is a physical door issue, you can increase the force on the motor to get past the issue, is it related to the weather? Do you have a wooden door?
@@oldboneybird change the force settings for now and change it back once the door has settled again, I have a video on settings force as well, have a look
@@iekeraamlevy3882 thank you for the comment, I'd you purchased new remotes, try the following first... Hold the button on the remote for about 15s until the led light pulses slowly... Then try again. If it still does not work, you will have to get a standalone receiver
One ET remote with two buttons which was previously added works fine but the other with 4 buttons flashes LED fine, but trying to program and add this 4 button remote to the gate does not indicate it is receiving a remote code from any of the 4 buttons. Any ideas why?
Thank you for the comment, you should be looking for a standalone ET receiver not programming to the D5Evo PCB, once you find the receiver, please check my video on programming to a ET receiver... ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3gYdM8pykzk.html
Thanks for the info. But the background music is not necessary. I would like to hear you only. Thus I don't like videos like these to have background music. That's me.
Thank you for the comment, short answer is no, but you can try changing the force settings, but be careful, the higher the force the higher the resistance needed to stop the door...
Hi, my ET 500 just stopped working, I checked all the fuses, replaced the battery, it does not beep at all, I can see the the LED lights are on and when I press my remote I can see the LED flickering, do you know what the issue could be?
Thank you for the comment, on a ET 500 with no beeping is difficult as the board uses beep codes to communicate, take a jumper and put it in place of the green wire (door release) and see if the board beeps
@@nicksandtrickssa you are a life saver, thanks man, I placed the jumper on it beeps and the gate is working again, does this mean my door release is faulty? I left the jumper on in the mean time
@@TheLadiesmanG what you can do is bend the pins, maybe the connector not making good contact, having the jumper there is a problem if you ever work on the gate as it will be on all the time even with the door open