RESIONE makes 3D printing more practical. This channel will share some experiences, practical skills, application scenarios and interesting prints about resin 3D printing from time to time. Welcome.
its two different resins ，M58 is a scratch resistant resin ，SP64 are not scratch resistant . SP64 not for action figures，and its not picky about settings ，you can use our setting or the original setting of your printer
@@sunghumcho8573 We thoroughly analyzed numerous causes of print failures from extensive post-sales case data, leading to the development of SP64 resin, which offers higher tolerance and consistency to address these issues. It is user-friendly regardless of user experience, printing equipment hardware, or printing environment. Its components are stable over the long term, do not settle, and require simple and quick post-processing. Successfully achieving stable prints on many mainstream LCD printers without the need for parameter adjustments significantly boosts the production yield of printed items.
when you say lower the ambient temperature do you mean in general or specifically when its printing? I'm getting some 80T resin and i want it to be as flexible as possible so if i need too i could get an enclosure heater.
What it means is that when the temperature is low ，the prints will become harder ！ this resin viscosity is very high ，So if the ambient temperature in your area is below 22 degrees Celsius, it's a good idea to warm up the resin before you print, and it's best if your printer has a thermostat feature.
Amazing work on the video! The detail and craftsmanship are truly impressive. I was wondering, is it possible to purchase the STL model you showcased? I would love to work on a project with it. Thanks for sharing your skills with us!
Is this resin no longer available? The link on this page gives a 404 error and when I search it on the site, nothing shows up. Is there a comparable substitute for it?
Sorry about that ，MS100 is not available anymore ，because the sales is not good so we cut it off last year ，we will develop something similar soon ，i will let you know ，thanks so much for the love and support！
Will definitely give this a try. I'm looking for something that's reasonably tough, but the big requirement, which seems hard to find, is that it doesn't wear off with a bit of friction. I'm not printing ball bearings or anything, but the parts need to be able to rub against each other a bit without powder coming off.
We will definitely recommend the Anti-impact resin for you ! This resin is suitable for your application needs，you can check our web resione.com and search Anti-impact！
Здравствуйте!!! Приобрёл вашу смолу! Она мне очень нравится. Но есть одно но! Точность печати отверстий очень низкая, размер уходит до 0.3мм. Причем печатал и на anycubic photon mono 2 и на anycubic photon mono m5. При разных настройках. Пробовал даже 2.5 секунды засвета делать. И все равно точности нету. Смолу перед печатью нагреваю до 33гр.
Yes，it compatible with M5S ，we have the settings on our official website you can download .You can boil the water ，and then you put the bottle resin into the hot water to heat it 5-10minutes，and you good to go ，make sure the cap was tight！
That's broly design from figure class. I believe you're adjusting the hand which holds Goku and switch to holds the energy orb. Nice painting btw. Hope to see the finish product soon!
what do you do with the water afterwards? Even after washinng models with IPA, they water is now contaminated. I guess having a kettle for resin-water only would be the best case, and reusing it.
I have the same action figures. I originally printed with the brittle resin and it was not good at all. I ended up using Siraya Tech Blu and Siraya Tech Tenacious with a 40/60 mixture and it still wasn't the greatest but I was able to put it together. The resin you used seems to be a lot better.
Blow-drying is an accelerated process of blowing out the alcohol left on the surface and then placing it directly into the curing chamber. Blow-drying also allows you to see if your prints have been cleaned, and if there is still resin left on the surface, to wash and blow-dry again.
