@brandonyin3288 hi, hope you enjoy the video. Because the controller is 4 channels , I added a extra 3 channels small remote for all the beacon lights. And the roof main beacon was using "JUWUBA" circuit board.
@TheMuhdfarid90 hi, not really. You need to cut off the original plastic pin. Then make a couple aluminium plate depending on the height or thickness you want and a coupler pin.
i do what you said and the servos work but when i try to =change settings in app it fkshes not connected after i try. ive uninstalled app and installed several times
sorry to bother you again. i am still having much difficulty getting the gt power 60 amp unit to work. im using a radiomaster mt 12 pistol grip and 5 ch rx. i have thr on ch 1 steering on ch2 5th wheel servo on ch3 and gear shift on ch4. i plug the servos into unit as the manual says and the red wires coming from the unit i plug top wire into ch 1 . 2nd wire into ch2 shift into 3rd wire and gear into 4th wire. the 5th is for sbvus and not used. gt power said i need servos which are not high voltage so i bought 3 servos and still have the same problem. thr is sporadic .steer servo stutters and hardly moves and the gear and 5th wh doesnt move at all. can you think of anything im missing . thankyou
Hi, sorry to hear you still have trouble with it. Let me try to make a video about all servo connections and you need download a GTpower truck L&S 60A apps on your mobile phone according the rest of functions work. Get back to you later.
Can you tell me where the 5 leads from the unit go to keg as t corresponding channels on the rx. They are not marked and nothing in the instructions. I’m pretty sure the 5th lead is not used because it is for xbus
Hi, when you look at the user manual pages 4, I think. It says the first 4 ch are for your 4ch receiver . The last channel is the SBus/PPM signal for the SBus recevier compilable. The first 4 channels depend on what your transmitter channel are. Normally the GTpower ch1 is steering, ch2 is ESC, ch3 is function, ch4 is gear shift. Hope that would help.
Hello friend please help me.. These days i am building scania r620 blue edition truck.. I using gt pro eu version unit like your truck.. But my moter does not get full power when active coupler switch but i can Hear the coupling sound... So what will Be the reason?
Hi, so you are using pro version 60A , right? It may be a calibration between controller and the gtpower module. Or may be signal reverse. Or the controller end point. Basically need play around those issues. For me I am not 100% fully calibrated yet till now😅. Which controller you use?
Hello.. I still got the problem.. I did calibrate the gt pro unit to transmitter but still have the problem .🙁. Does your truck motor increase the power when active the coupler switch?
you need to use 2 separate suspension sets for rear mate . this only pushes the front axle down . when on a lift axle the hole truck dont lift only that axle. what you did is all in one rear suspension set . but its clearly wrong buddy . just a tip use single axle rear suspension sets ,2. use a scania 770s twin steering lift mechanism and you will archive the correct out comes. that look spot on. sorry but this looks wrong as on if in Columbia where all trucks are on a lean. lol😂
😅😅😅😅 , thank you for your sincere comment. I just use whatever I have and try not to get over the budget for all the mods. Hope you understand. I know I can't compare to the actual real truck can do. But I love to do what I can..😅. And I do like my outcome anyway. If I have more budget, I may do better or buy a new rc truck (scania s770 8x4)😅.
can you make a video on how to set up s.bus. it should be about the same for nearly all controllers . most use flysky. . just want to know how it all works whats the set up involved usually. what did you have to change around on comtrol. stuff like that. appreciate your shows. keep them coming. love trucks
cam you show in videos how to set up a s.bus on control through to the light sounds unit please. i hate the other way and s.bus i can work everything with aux switchs . please help us all in this same control. or the white flysky 10ch
You are so fucking craesy you does not know to what you do. read the instruction of tamya exectly may be in german, if you dont understand britisch language. its a tip from Austria and from Norway. cherrio and keep trying whith the poor Volvo
Hi, you can try aliexpress. AU $439.16 35%OFF | Hercules Lowtop 1/14 RC Tractor Truck 6*4 Remote Control Construction Vehicles 540Motor Toys For Adults Arocs Bz Model TH16851 a.aliexpress.com/_mMZupfY
Have a look these. AU $211.79 | G.T.Power Container Truck Lighting And Voice Vibration System PRO With 60A ESC Output For RC Car Parts a.aliexpress.com/_mM7MyAq
AU $212.86 17%OFF | G.T.POWER Container Truck Lighting and Voice Vibration System Pro For Tamiya RC4WD Tractor RC Truck Trx4 Toys New Year Gift a.aliexpress.com/_mPIVleK
Do you have some off the old update files ? I was upgrading to 2.9.2 via G.T powers website, now my truck has to be plugged to my pc via usb to work, still no lights works, if i take out the usb cable the radio/controller disconnects and the radiotransmitter/sender stop getting power. When i put usb cable back in the controller connects and everything else without lights works... G.T power does not answer any one my emails or messages on their website Do you have som of the old files so i can downgrade or have any clue what i can do to solve this problem ?
Sorry mate, been away for work didn't get your message. I don't think I keep the old firmware file. And just keep message G.t.power on there website. They reply little bit later sometimes.
Nice truck. How did you built in the MFC-03 AND the interior? According instruction we should not attach seats and dashboard when MFC unit is installed 🙂 Maybe you have link with an instruction?
😅 yes, little bit work. All you do just install all seat and interior then connect all connection on MFC then mount on back wall behind the seat using double side tape or Velcro tape.
Hi, hope you enjoy the video😅. The light above the side door on rear body was connected to a RC4wd remote light module. It has 4 lights output you can see on the video.
Nicely done my friend............a bit complicated..........but your investment has paid off because everything works without the limits of other systems...........this hobby has never been cheap...........but buying stuff that works well is very satisfying...........nice truck............would be cool to see it pulling a trailer 👍
Thank you for your comment. Yes this hobby is costing 😅. But if you are a creative person then you may save a lot(DIY mods) and it is no limit. Are you building yours too? Enjoy it! Yes, I do have a short video of this rc truck towing a B-double trailer, please check on my channel for all video. Enjoy RC and keep up!
Hi, As soon as my receiver is on, the lights are on. I can change the flashing sequence, but there does not seem to be an 'off' (no lights at all) mode. How do you switch it off by remote?
@@funboxetoys1962 Thanks for your quick answer. Apparently mine doesn't. Tried it with transmitter and servo tester. Could you tell me your endpoints? If I can't get it to off, I guess I will have to put a switch on the power leads.
@@lievenschiltz825 hi, the best is contact the seller , ask them about the light you have with that problem. Also my mistake. I just remember that light didn't have "off" mode too, and I was using a external remote controller module to turn on & off.
You speak in the past tense. Your light also didn't have an 'off' mode too. Does it mean you exchanged it for another one that does turn off? or are you still using an external remote? Personally, I wouldn't mind using an electronic switch.
@@lievenschiltz825 yes, I did use a external remote to turn it on & off. What I did was set up the flashing pattern first with a servo tester then plug in a external remote, that would always flashing same mode.
Congratulations on your modification. I have had a bruder forklift for several years. I have always wanted to do rc modification, today due to health problems I am looking for information and luckily I found your video, I am looking forward to seeing more videos of this modification to bring my modification to completion. Could you indicate how you have connected the steering system to the servo? Thank you very much.
@@funboxetoys1962 It would be very interesting to see the whole modification, including how it lifts the nails from the machine and how it does the maneuver of lowering the nails.
awesome man awesome I just shared with family and friends to subscribe to your channel to boost it please look at mine and share and help the old man out appreciate it thanks
