@djsprc no I haven't. I've been on a RC spending spree last couple months and it's not something that I need but would be nice to have. Maybe I'll msg them and see what they say.
I’d rather be honest with you. is customer service is slow. I’ve been waiting more than a year to have my bottom of my stand replaced. It keeps on Boeing.
@djsprc ok that good info to know. Little disappointing that they wouldn't take care of you right away? I just had RamJam Racing send me like $70 worth of stuff for free because of a mistake and it arrived 1 week later
@@nathancunningham8717 you would think if somebody makes a video about your product that yes you would make sure to take care of him, but I don’t mind. This was not a sponsored video. I was supposed to buy one of his ramps, but after the issues with the stand, I decide not to get them. Let me know if you ever decide to buy one of his stands and you get it. I am curious.
That size of vehicle I would go minimum 50. Or 70 that’s what I would do again it depends on you. You could try one and see how it handles if you like it keep it if not, you could change it to the other one and see how it handles.
Thanks for sharing all these great tips. 👍👍 I like the explanation on lighter fluid in the rear than the front. Great advice. I don't race or anything like that but it's good to at least know about how a car reacts on landings. 🏆
On the Traxxas slash. The rear knuckles are fixed should not have any movement. The only thing I can see there were knuckles or not at the correct place meaning the right is in the left and the left is in the right. They should be facing in words a bit.
Went with 35wt for my light redcat volcano epx pro, will update in a few days when it comes in, running it mostly stock for now besides steering knuckles and a arms etc
Thanks for the video! I didn't know they released the sway bars. And while I ordered them I also found the center diff upgrade. Installed both upgrades yesterday. Finally the Puma is technically on par with the HPI Flux WR8.
Aloha please I need help finding what oil weight to use in a Fms FJ40 1:10 it is pretty heavy at 15lb mostly being top heavy as well, I want to stiffen the ride as it bounces all over the place, I don’t want to convert to a leaf spring conversion kit. Want to keep the coil springs. Will be building it as a trail and some crawling. What weight oil should I use please help!
What I would do is start maybe with 35 weight and possibility to go up to 45 weight. Start with the 35 see how you like it if you feel it’s not stiff enough go up and wait unfortunately I cannot tell you to go with a specific weight. Every machine are different. As a reference if you look at.Trx4 truck they come with 30 weight. I have my Axial Wraith with no spring. I am running 30.
@@djsprc thank you for the reply back! This is very helpful 🙏🏼 I seen losi has a bundle of different weights on amazon I will start with 35 and work my way up if need. Do you say the heavier the rig gets the heavier the oil?
Hello, I'm looking to upgrade my old Ender 3 by purchasing the Ender Sprite. After watching your video, it seems quite easy to install. However, do I have to modify my firmware? I made some little changes to my old Ender 3 by modifying Marlin. Best regards 😁
Hi there, yes you will need to upgrade your firmware to correspond to the sprite. You may even be able to find a firmware already built up for your printer. If you have experience with Marlin then you should be able to add it. I used to run Marlin now I’m running.Klipper. Way better firmware, and you can do upgrades anytime or modification without needed to redo the complete firmware. But yes to install the Sprite is not hard at all.
@@filapraha if you plug-in two fully charged batteries and they are Lipo the light should be green. If it’s not green that means it’s in non-low-voltage what you will need to do is take your remote. hold a trigger in full reverse turn it on then plug it to fully charge Lipo to the boat. continue holding for at least 10 seconds. The light should turn green meaning low-voltage is activated safe to run Lipo.
The reason is my local Hobby shop did not carry the other model in stock. They only had this one 6814. I have ordered the other one. I will see how long this one last.
On which way you need to turn it depends how your alignment is off. You can do it with the vehicle on and remote, but be careful not to put too much pressure to break any gears in your servo. I would make sure that your trim on your remote is centred turn everything on the servo will centre itself then I would turn everything off and do the alignment
@@chuckdeezy8380 that’s unfortunate. Yes, there is some play in it. You might’ve put it a little bit too close to the side fan once your print is done. Loosen your screws and try to move it out of the way. The other thing to make sure that you don’t have your wires on that side. If you do flip it opposite, it might be your wireless touching too.
bro. you didn't even boot it up and show it works. Any issues with the Touch Probe? My ender 3 Max I just installed a Sprite and won't work with my CR Touch, I have to connect the probe directly to the mother board with the original cable for it to work. Seems like this is a common problem. But yeah, always a good idea when you show setting up new hardware to show the finished product actually running. This way you can address any potential problems you encounter.
Hey i wand to change the oil in my 140mm shock's but i use then for my fanatec csl dd padel's any suggestions on what type of oil i shut use if im using them for my gas and brack padel
Thank you . I m still afraid to mess it up but if I count the turns I can always go back but I ll get it right . Mines brand new and reminds me of girls with big boobs where the nips are pointing to the side 😂
If iv been using 2s lipo the whole time on this one would I need to do anything before I try a 3s? Or can I just plug and play? Iv never had a 3s battery never got around to it even tho it’s capable.
Djsprc, nice run of your sonic wake V1, I am Linden Stewart from Georgetown Guyana in south America, I have the sonic-wake V1. 😊the problem with my Sonic-wake V1 when ever the boat flips over, it takes a long time to self right, about 3 minutes or more. By that time the water gets into the battery compartment and the boat won't start, I have to go to retrieve it. Is their anything you can recommend so I can correct that problem?
Just make sure that your battery is positioned at the correct place half the time is a battery not position correctly will prevent from flipping back. Make sure you use some tape around your hall hatch to prevent water from going in.