@@DrJacks НЕ ХОЧЕШЬ СДЕЛАТЬ ВИДЕО ПРО СТРЕЛЬБУ НЕ С ПОРОХОМ , А СО СПИЧЕЧНОЙ СЕРОЙ ? И СРАВНИТЬ ПРОБИВНУЮ СПОСОБНОСТЬ ПОРОХА И СПИЧЕЧНОЙ СЕРЫ ? ЕСТЬ МНЕНИЕ ,ЧТО СПИЧЕЧНАЯ СЕРА ПО ПРОБИВНОЙ СИЛЕ - ПРЕВОСХОДИТ ЧЕРНЫЙ ПОРОХ ☝🏿
I AM a DIY muzzle loader from propellent to paper and all possibles and self gunsmithing. I must admit? I have considered a "Dreyse" system as they are a valued as a historic systems, but hard to enjoy due "in my opinion" to their ammo. I have not done homework for the ammo.
It is really easy to manufacture, as far as you check out the correct cartridge length (bullet included) before building any paper cartridge. But it takes its time. 😅
Yes, I use normal percussion caps. Ammo making is very similar to Chassepot ammo production. I have a video in German where it is explained. But there are lots of vidz in english how you do it.
Hi, the model you're talking about is the earlier M1835 and M1840 Dreyse pistols. I have one of each too. But there were only built about 100-200 pieces of the M1865 pistol. If you want to buy one, you can search for it on gunsinternational. They are incredibly expensive. Dreyse constructed the M1865 for the prussian military as an officers sidearm. But it was abandoned by the military due to its high production costs.
Nice . . . I want to see moore ! Make a longer video on this very intressting pistol and do a lot of shooting, so we can see the results. Does it have good precision ? I`m waiting for your next video ! Peter in Sweden
Sehr interessanter Umbau. Danke dafür. Wie wird das Patronenlager nach dem Umbau nach hinten abgedichtet? Einen Gummi gibt es nicht mehr und die Hülsen dürften zu massiv sein, um sich zu weiten. Ist dazu nur der Hülsenmund ausreichend? Es wird vom Reinigen des Verschlusses gesprochen. Wie sehr verdreckt die Waffe und wo?
Ja, das hast du richtig geschlussfolgert. Die Abdichtung erfolgt am Hülsenmund und dichtet zuverlässig ab. Der Verschluss verdreckt hauptsächlich vorne am Kopf durch Schmauch. Innen fehlt nichts bis wenig, solange man keine Zündhütchen-Durchbläser hat. Ich habe die maximale Schusszahl noch nicht erreicht, wo ich sagen würde jetzt geht nichts mehr. Allerdings waren 30 Schuss das Maximum. Man könnte aber sicherlich locker nochmal genau so viele oder mehr abgeben. Kann aber nicht sagen, wo da die Grenze liegt. Einem Nachmittag am Stand steht jedenfalls keine Reinigung im Weg. ;)
This is the largest rifle I have ever shot. But it was quite funny XD There are only some match ignition rifles out there, which are larger then this...
I talked to an expert of percussion shotguns. He told me that they used to hunt with these long rifles straight above the head shooting in a 90 degree angle above right into the bird swarms. Through the large barrels even goose swarms in 100 meters or more height could've been hunted.
Hi, I am still waiting for one part being repaired by a gunsmith. I will finish the project as soon as I'll receive this part. Because I really want to shoot this one! :D I think I will make a video of stock restoration in the meantime
It is easy to find, if you'll know where to search for it. ;) If you search any gun projects like this, just text me what you are looking for, maybe I can help you, because I am selling historic guns. ;)
I recently came across an article where these wall rifle model was described. And apparently there exist a rifled version and a earlier version of this gun which was without rifling.
Das mit dem Pappstrohhalmen ist Genial👍 Und ich dachte schon ich wäre mit meinem "Post It`s" für meine Sharps Patronen fuchsig😆 Bei den Zündhütchen habe ich immer einen "Flügel" ausgebrochen, dann rieselt Pulver von der Ladung rein, allerdings habe ich die ZH in Pappscheinen mit Loch gesteckt und dann mit Pappierscheiben abgedeckt. Wobei grade diese "Pappdonuts" einen das Basteln echt vermiesen können, zumindest mit Locheisen. Als Pulver kommt bei mir Pow Ex oder Wano FG rein. Da soviel das die fertige Patrone stram im Lager sitzt, sonst gibts Zündversager.Als Geschoss nehme ich die 45-405-FN GIesskokille von Rcbs( ist für 45/70 ein klasse Geschoss) und Kalibriere sie auf. 446 runter. Das Geschoß bekommt dann noch eine Art "Paperpatch" aus einen Papierklebeband damit es fest in der Paperhülse sitz. Was das Zünden noch etwas verbessert ist wenn man die Nadel etwas anraut...hatte auch oft Versager wo bei der Demontage das ZH mehrmals durchschlagen wurde, aber wohl die Reibung zu gering war. Die alten Gewehre wiederzubeleben macht richtig Laune🙂
Hallo, die Pappröhrchen sind bei mir 51mm. Geschosse nutze ich 11mm Chassepot-Geschosse, wie sie auf eg**.de zu finden sind. Diese haben: -11,5mm im Durchmesser 26mm Geschosslänge -380 grn Sie gehen aber besser rein, wenn sie auf 11,46mm kalibriert werden. Auch 11mm Mauser Geschosse müssten gut gehen. Allerdings hatte ich auch schon Chassepot die 56mm lange Pappröhrchen benötigt haben. Die Patronenlagerbohrungen waren damals nicht so präzise wie heute, daher die Schwankungen. Ich empfehle die Patronenlagerlänge vor Bau der Papierpatronen zu ermitteln. Die Papierpatronen sind dann richtig in der Länge gebaut, wenn sich der Verschluss mit leichtem Druck schließen lässt. english: Hi, the cardboard sleeves I use are 51mm. I use 11mm Chassepot bullets as can be found on eg**.de. Sizes: -11.5mm in diameter 26mm bullet length -380 grn But they fit better if they are calibrated to 11.46mm. 11mm Mauser bullets should also work well. But I have also had Chassepot rifles that required 56mm cardboard cases. Chamber bores were not as precise back then as they are today, hence the variations. I recommend determining the chamber length before building the paper cartridges. The length of the paper cartridges is correct if the bolt can be closed with light pressure.
Hallo, ja die habe ich tatsächlich gefunden. Allerdings wackelt der Prototyp noch zu sehr. Ich muss noch einen zweiten bauen. Ich versuche dazu ein Video zu machen.
So ist es. :D Meine Werkstatt ist tatsächlich in einem alten Badezimmer eingerichtet. So kann ich auch gleich spontan ausbrechende Feuer einfach mit der Dusche löschen XD
@@DrJacks Dachte zuerst, dass du mit "spontan auftretende Feuer löschen" metaphorisch etwas anderes meinst xD Du hattest die Metallpatronen fürs Chassepot angesprochen. Machst du über so ein Umbauset noch ein Video? Besonders die Legalität in Deutschland würde mich interessieren. Einerseits bleibt die Zündnadel erhalten, andererseits ist das Gewehr dann sehr ähnlich zu einem WBK Pflichtigen Gras Gewehr.
@@heavengameful Ja zu den Umbaukits wird noch ein Video kommen. Ich möchte aber inhaltlich hier noch nicht vorgreifen. Aber so viel vorweg: Man kann bei dem Thema Umbaukit durchaus positiv gestimmt sein.
This was only a shortening of the other videos. For extended version please watch the other video. Thank you! I am still waiting for some parts of my favorite gun smith to move on. But unfortunately it will still take some time.
Thank you for your question. In the 18th century most of those guns were manufactured for noble men. They liked to pick up the shot game with the bayonet and of course used it to kill game when was not shot accurately. There also existed double barreled percussion war shotguns with bayonet for the first line. They were used by the so called voltigeurs in the Napoleonic wars.
Disassembling worked so far: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-H4CXrNEAv5Q.html Now I must gather all the parts, that were destroyed during diassembling and then will move on. спасибо за просмотр!
I assume you shoot this chassepot? What method of construction are you using for the ammunition? I am experimenting with both paper and plastic 12mm straws, RWS musket primers and a thin rubber disk taped to the base, and a range of pure lead projectiles from .452 to .460 diameter.
I use 12mm paper straws expanded on both ends with a spiral drill atm. As primers I use CCI musket primers, filled wih BP and glued on a thin cardboard. Projectiles are the ones in original 11mm Chassepot size with 380 grs. In near future I will change to a kit which allows you to use metal cases with large pistol primers while still using the needle ignition. This means the needle ignition function is not changed and thus the ignition mode is not changed. So this will bring me some advantages, as you have no more issues with decentered bullets and a higher accuracy to achieve always same black powder load in all cartridges.
Yes, you are right, there are different methods for removing rust, electrolysis, steel wool, grindstone, steel brush, and vinegar, just to name a few. I decide in dependency on time effort, area of the rust/ corrosion pits, active rust or inactive rust, and the abrasive or nonabrasive method. Here I decided on the abrasive method, which is, besides other methods still state-of-the-art, to get rid of the rust colorization of the metal in this area to homogenize the appearance of the weapon as a whole. Most of the time I am still a friend of nonabrasive methods, still using the electrolysis bath, which is among the restorators at the national museum abandoned. Why? Because under a microscope you will find out, that the electrolysis changes the metal surface into a sponge-like condition which is far from the original condition. But I aim for bringing the guns back to a state, where they are able to be fired again while preserving them in the best possible collectors state not erasing but considering their age. Thanks for watching and for your comment!