Hi I had purchased one. I found a two pin socket on it. Do you use a 2 pin male to female or 3 pin male to female cable for the mower ? Which is better
@@BillVance-l7u you’re right Bill, they asked me this before but apparently the footage of that process was lost somehow. I searched the hell out of it but in vain. Thank you for your visit and your support 👍😀
@@TheSnifmister I believe to remember that you have to pull the handle in the “open “ position while putting the panel back. Hope this helps. Thanks for visiting the channel 👍😀
@@mikedr1549 well, over here it is prohibited to film over someone’s property … at least intended. In this case, although it was not intended, it was not possible to film without including that property, so it was better to blur it out. Thanks for watching and for taking the time to comment. Have a wonderful day 👍😀
Very unsatisfying, but I think it was my fault: I did put several layers when the previous layer wasn’t dry yet and thus messed it up a little. I will have to do the whole process once again when I have the time. 👍😀
Were you successful in correcting your issues? How hard would you say this is to do and what would the total cost of supplies be? How long did it take? I have no faults but my brake pedal is softer than i'd like and I have no idea how old the fluid is.
It worked perfectly and the tools were very helpful. I don’t know the cost by heart, it’s too long ago , but I’m very glad I did this service. Thanks for stopping by and for taking the time to comment 👍😀
Thank you sir , I’ve just done the service on my tdv8 and grateful to you for showing me the correct way of installing the new oil filter as I had tried to install it with the screw top already pushed into the new filter and it wasn’t seating properly so your video put me right 👍 excellent video on this great engine
Hey man I need some help from you! Is there an email you can share with me! I am receiving a message from the system that states “The Suspension not in Customer mode” after I tried to do height adjustment using the Gap tool
Thank you for your interest, but first I have to say I’m not a technician. If it was my car and in this situation I would clear the error first. If it came back I would reset everything to factory settings so it would disappear. Then I would try again to set it to the height that I would require. Hope this helps 👍😀
Very interesting video! Thanks a lot. Do you mind telling me if there are a pair of those boxes in the front bumper as well? Thank you very much for sharing!
In fact that is a good question, but no there aren’t because there is no blind spot in front of the car. Those sensors work for a car that sits behind in the blind spot and even when that car is at the left or right side of your car but not when it is in front of you . Hope this helps and thanks for watching the video 👍😀
Hello, thank your for you video. I don’t think what the manual is saying is wait 2 min before removing or adding the positive, but rather wait 2 min before opening a door or acting on the car before disconnecting and after connecting the battery. What is really happening once removed the Negative wire: Nothing, as there is no potential between negative and positive of the car.
Hello Damien. Thank you for watching the video and for taking the time to comment. The reason for waiting at least 2 minutes (some people even say 10 to 20 minutes) is that there are a lot of capacitors that still can have some load inside and they need some time to get rid of it. At least that is what I read about this issue. I’m not a technician nor an electrician so I can not guarantee this is a correct explanation but that’s what I could find about this problem. Hope this helps 👍😀
I would say a helmet or some kind of eye shielding should be required. Even though the arc flash may not cause immediate discomfort, it will definitely harm your eyes!
Hoe lang heeft u de tv? Bij ons hetzelfde geval, hij is pas 2 jaar oud, ambi light werkt ook maar voor de helft van de tijd, ik ga ook maar eens met tape aan de slag! Dank u voor het uploaden
I have the same problem. It fixed with a new TCON board for 10 minutes but the tape trick should work. If not i am going to remove all the resistors near the LCD as that should fix it. But the tape trick is much safer
Hi, thanks for the video. I was wondering why you didn't use a pressure washer and snow foam to wash the car? I think it is quicker (and in my opinion more enjoyable). Adam, London UK.
I had to put the water pump inside during the winter and it’s not yet installed back in the shed because it could still freeze and get broke … but I used a wash and wax product (soap and wax) and the 2 bucket method. Can’t wait for warmer periods so I can use the pressure washer for sure 👍… thanks for watching and for talking the time to comment 👍😀
It still works today … just sometimes when it is really wet for days the error can pop up shortly to go away back when it’s dried up in the garage. I suspect I didn’t seal the plug well enough and a technician from the dealer advised to wrap the whole thing in a plastic bag before putting it back . Hope this helps and thanks for watching 👍😀
It appears your rear spring is flat which mean it's lost it's arch. Probably needs replacing. Normally when replacing the rear spring it make the car set too high.
So i had 2 issues with the 50inch version, one is now fixed with this solution which is great. However the television makes this really annoying high pitched sound. Ive found out that by reducing the contrast of the television to 0 almost eliminates this issue, however the screen is very dark now. Anyone knows a solution to this?
Sorry to hear you have that issue with the sound … did you try out a different sound-preset? This could perhaps filter out the high pitched sound. Thank you for your visit and for your contribution here and I really hope you can find a solution 👍😀
Maybe solder a big capacitor on the voltage lines of the audio amplifier, close to it. one elko and one ceramic. 100uF and 10nF. if the audioamp has double voltages you need it twice. pitch is the switching supply get into the amp, you can also look or there are capacitors on the power board has bolled caps on top, replace these,
Wow, yellow on red interior? Looks like a bleeding banana. Please tell me this was not a factory combo. To each his own, great job on the restoration though. Thanks for sharing!
I even didn’t have to reset it, if I remember it correctly… but you could try to reset it with the GAP tool, and if you don’t have that you could try to disconnect the battery for let’s say 5 minutes to reset it. If that didn’t help, the reason could be also the sender of that particular wheel could be defect also. Hope this helps. Thank you for your interest and for your visit 👍😀
You could also exchange the sender from one wheel to another and if the error goes to that other wheel you can be sure it is the sender that is defective… just thought of that method! Good luck!
I need help please...does this camera records 24/7 continuous and for how long can it record on the sd card ( I mean for how many days can it record continuous) please
For anyone looking for information: The cables that send signal to the screen LED's are flat ribbon cables the ribbon cables get wiggled around or the contact lift a little bit and then some section of the screen/portion of the screen has lines on it. The best way to fix this issue is to apply pressure to the ribbon contacts once they are plugged in, but first try simply removing, then reseating the ribbon cables, if this does not work then applying tape force the ribbon to be flat and parralel with the board pushes the contacts down. It seats the cable properly in its home and makes a good connection. Just finished doing this to my TV, it fixed glitching and horizontal lines.
In my case it didn’t push the contacts down because the tape was above AND on the underside of the ribbon. Thank you for your contribution here, it’s very much appreciated 👍😀