Лучшее на RU-vid
Кино
Авто/Мото
Видеоклипы
Животные
Спорт
Игры
Приколы
Развлечения
Хобби
Наука
Авторизоваться
Зарегистрироваться
Kroonstad Motor Engineering
13
3 521 406
Подписаться
7:25
Head Service Aprilia Picasso 650
Год назад
4:59
Hyundai Accent head resurfacing
2 года назад
2:12
Yamaha Motorcycle Reboring
2 года назад
3:19
Replacing small end bush | Fiat 780 Tractor Connecting rod |
2 года назад
5:17
Repairing Damaged Cylinder Wall | Resleeving Cylinder Toyota 4AFE |
2 года назад
Комментарии
@robertoudokrapf453
13 дней назад
OLÁ 03/09/24 Informe-se antes de fazer vídeos errados.
@Mrgameguy211
2 месяца назад
yeah nah, not sure it was the head that failed, i think your problem was probably in the lower end to start with or maybe lost oil pressure. send it to the machine shop mate, it'll buff out im sure.
@DatG-sx1co
7 месяцев назад
Old method. Just use sleeve puller instead
@dennissharpe8356
8 месяцев назад
Makes the most sense
@nikutb6798
8 месяцев назад
fine work
@ChevyBoyE
9 месяцев назад
What is the price range to get this done ?
@marielosdominguez9082
11 месяцев назад
En cuanto lo tienes
@marielosdominguez9082
11 месяцев назад
E😊 ]recio
@hengkyiw
11 месяцев назад
This is the safest way without damaging the cylinder block. But it takes longer than removing it with long thin chisel.
@user-mp9hn6vc8o
11 месяцев назад
این پرایده چقدر گوشااااد کره😂😂
@homesteadhaven2010
Год назад
They make a ridge reamer. Lmfao.
@scottlarsen8788
Год назад
Need a ridge reamer!
@AxelP33
Год назад
Id this a Berco boring machine ?
@user-te8bs4qz4o
Год назад
Hey boss, what is the location?
@sebastianrenzoramosvergara2268
Год назад
buen motor perdura por muchos años
@erwindiolata5506
3 месяца назад
🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉😢🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉
@willnorthcuttiii4905
Год назад
I love machining
@--Dake--
Год назад
Вот это точность а.... айм в шоке😮🤤
@Cobra427Veight
Год назад
Very bad , use a lpg torch or rod heater , someone has shown you wrong way to do it .
@phils4634
Год назад
Looks like the aftermath of a piston vs. head "collision"
@philandlyra3365
Год назад
Flapper wheel every time.
@luiscoslop776
Год назад
Y se debe de dar por arriba y también abajo y dejar que la válvula solo siente en el centro de la válvula.
@luiscoslop776
Год назад
También eso se puede hacer con una piedra, se instala volteada en el mismo taladro para bajar el asiento.
@dieselpratamadisel321
Год назад
perfect result 👍👍👍🙏
@mobariksadi9394
Год назад
Recfification di soupape
@kenmurphy4317
Год назад
Why can't you just drop out the bottom
@rezakheradmand5341
Год назад
😧wTH
@k.o.mo.
Год назад
無理やりピストンに挿入する様ならピストンの、挿入する部分が小さいか何かしらだと思いますよ私ならスルスル入るまで削るか、何かしらしますね固すぎたら弊害在っても一利無しですからね、
@miro_yo
Год назад
It’s similar to the machine that i work, AMC 1800
@robertryan4485
Год назад
I still have an old-school ridge cutter then we went home the s*** out of the tractor sleeves check the ring Gap and put rings in it
@darrellhart9363
Год назад
Man that cut looks better than 50 thou to get those pistons out.
@johnneedy3164
Год назад
So use ridge reamer
@ikvanachter6002
Год назад
He has more tricks in his sleeves !
@keysejkeysej
Год назад
Why you do t take out it from below?
@danlindeke2561
Год назад
For DIYers, there is a wrench operated ridge reamer. Only about $25
@ЭнверАлиев-ъ8к
Год назад
Это пи... Дец
@Санёк54-н3к
Год назад
и такое бывает.до победного тянут на ремонт встать
@jorgemairena2289
Год назад
Me imagino k kedaria x lo menos a 100. Solo sugiero?
@Fil702
Год назад
Толку перегельзавать дай бог хватит на 50 тыс
@stevenmkhulu7153
Год назад
Amazing work
@SpeedracerMach
Год назад
Do they sell one of the machines at harbor freight
@diegogarcia4614
Год назад
Motor fiasa ?
@Cobra427Veight
Год назад
Looks like a Berco , Nice to use .
@javiercampos3255
Год назад
Que es eso 😱
@konanizwothe1606
Год назад
Do you guys do engine rebuild on the K2700 I have a k2700 that over heated and stopped moving
@robinjoseph3347
Год назад
Do they follow any drawing
@ebbeweber1310
Год назад
Old Opel OHC engines had this type of conrods. They always had to be preeheated before mounting the pistons...
@hakandelice4291
Год назад
İşte ustalık bu teknik adamı severim
@ДмитрийДвулучанский
Год назад
Странно, выглядит как новая.
@ДмитрийВдовин-ж2т
Год назад
вопрос в другом, не как вытащить, а сколько он проехал, вот вопрос?
@user-pt9to5wk2v
Год назад
Это что гильза такая?