really helped. Тhanks

❤😂🎉🎉🎉🎉❤❤❤❤ thank you very much you've just saved me hours of trying to work out what it is I've got a slight water leak nothing to do with the washing machine itself put the water at worked its way into the machine obviously filled up this tray so I just typed the washing machine to the side emptying the tray washing machine fixed easiest and fastest repair I've ever had

This helped me. Opened up the back, a mouse had chewed up the styrofoam float and the switch was stuck on. Vacumed the styrofoam, pushed the switch down and voila. Machine works. 😂

Four years on and still very useful! My old Clarke Rebel compressor had stood for many years unused and wouldn't start. I was about to start taking it apart to test all sorts of electrical connections, then found this! Mine has a similar trip switch in the same position (well hidden!) and after I pressed/reset it, the compressor started right up. so thanks very much! 😃👍

Ist absolut gleich mit dem Weldinger Gerät. Halt nur in gelb😉

You saved my life 😂

You, sir, are an absolute godsend, a scholar, and a gentleman.

Brilliant. Saved me a good few quid 👍

Thanks, manual is rubbish! this was super clear

Hello there, I have just started the search for information to fix my air compressor Makita AC1300. Your film is the first one that I have come across. Can you help please. The problem I have with my compressor is that it will not restart after it has run low of air. It will start from the beginning with no air in the tank and build up to the required pressure. But once the air as depleted down to a lower level it struggles to restart. It just turns over slowly and does not restart. If the air is completely emptied from the air tank it will then restart. I have had the compressor for some years.!I bought it off eBay and it was only a matter of months old. It was stated that it was an ex display model ??? It may be better if I take a film of what I'm saying is going on with the machine. If I upload it onto RU-vid I can then let you know the link. Might be can be for other people to repair their machine with the same problem. Do you think it might be some pressure valve or sensor. Thank you for any help. Kind regards, Daniel King.

Thanks dude! Good video though I would recommend taking the other side of the ball off so you can do those fiddly screws, I lost the washer inside the machine, managed to get it back out with allot of shaking though

Had one of these a couple of years and didn’t use it last year and struggled to start it until I watched this. Cheers 👍

You sir are a giant among men

What was the outcome of this?

cheers ..great help

Thanks for the tutorial. I was able to change mine in less than 5 minutes.

NO WAY

Thanks, your video is always there wenn I forget how to start the engine

Thanks, I wondered why the band saw I got secondhand made a weird whine when i plugged it in, thought i'd have to buy a new NVR - turned out the in/out neutral wires were round the wrong way. You just saved me some money on a new one. Scary thing is, i got it from a business and it had been PAT tested

Thank you so much! Just saved me a ton of time!

Where's the instructions on how to assemble the unit. Those pictures are meaningless.

I was just about to throw mine out too, until I saw this video. Have a different brand and model but it has a reset button! Thank you very much!

Thanks for this. Easier to follow than some others as can clearly see what you are doing at each step. I did however take both sides of the ball off which made accessing the screws on the non filter side much easier. Once again thanks.

I called the Dyson service phone number today and was told that this part is not available for purchase by an owner of a Dyson vacuum. It can only be repaired at a Dyson Service Center.

My brother in law also got issue with his brass cutter from aldi, the blade stop spinning on the 2nd attempt.. what should probably the cause of this suddenly blade stop spinning.. thanks

Great instructions, thanks for your help 🙏🏻

Thank you for posting that. Just the help I needed.👍

Thanks Foxtons. No water in base ... but mice had nibbled the polystyrene float and small pellets had got under the block, lifting it, to prevent the pump stopping.

All well and good, but you didn't mention what chain to purchase if you're changing one out. I have a different model than yours. I threw the original chain away--very dumb--and replaced it with an S52 which doesn't fit well around the knob and the chain fits very loosely. I'm constantly having to put the chain back on. The online owner's manual says to use a "91PJ052X" replacement chain, but if you walk into a big box store the chains are identified by length and these codes: S50, T50, R50, S52 and so on and so forth. Can you tell me what chain is on your model. There is one section of tooth on the chain that will have the part number. Thank you.

Does anyone know what size chain you need to replace this with? Lost my manual.

Thanks for this, all others seem to be rambling on without getting to the issue. This presentation of yours got straight to it and clearly got to the source of the issue. Saved me the cost of a new washer❤❤❤

Thank you

That one screw on the back side that holds the bracket together was a pain to put back in. Other than that it was easy. Some engineer needs to be taken behind the woodshed. Put all the screws on one side Great video. That you!

Most useful and needed video in history. Thank you. Was about to buy a new one

great stuff. Been wondering why mine didn't work, i hadn't used the other spacer 🤣😂🤣😂

Thank you very much! Saved me!

These are all 240v only good in europe basically

I fkn love you mate! Saved my bacon

Great video - easy to follow even for a non DIY person like me! Thank you

Really helpful....

I have just replaced our brocken hose using your step by step video. It now works brilliantly . Thankyou very much

They reset button hasn't popped out but still won't work I only use it now and then for my car tyres I've noticed there isn't any oil in it anyone give any advice.

Bless your soul

great video very informative and helpful

I had been polishing my carpets for a few months.....before realising the hose was working but not the carpet head which was just brushing with an asthematic wheeze....now fitted the new pipe and the dust mites are history......Great video. I took off both sides (wheels) for more access.

Any temporary fix idea?

Great video. Really useful with clear and easy steps.

This video saved me getting into a lot of bother thank you very much.

I need to press this reset button on my compressor everyday. When the pressure drops from use it does automatically switch on. What is the cause of this? Is there some part to replace?

You are my angel my friend, i am very worry coz my compressor wont work just notice tonight and decided to find technician tomorrow to fix it, but try to consult Dr. Y.T first and you came out then watch your content in few seconds and go out to check about the botton that you mention .fortunately i hit it.. Thnx very much. Im subscribe . Give me your shout out on your next content really appreciated.. from philippines