I have one of these and put it through the torture test. Crawling under the house, lighting under vehicles while repairing them, extra lighting while painting inside etc... With the use of an extra battery pack this light has been extremely useful. After abt. 2 years of use one bar has stopped working. 4 of the 6 retaining clips that secure the PCB light bar internally had broken off and the first LED on the TL-938 LED light bar had failed. Currently sourcing another SMD LED to replace it.
I got nothing from watching this :( I need to know how to add essential oil and if it has a pad that can be exchanged and where is the spot to put the pad I can’t find it. Instructions suck on the pamphlet and I’m confused
I've been searching for information on changing the knife blade in my inherited HDX utility knife. So far everything shows me what I have already figured out - HOWEVER, still have not been able to learn the "SECRET" that makes this simple task impossible for me to accomplish!! - - - HOW do I get both sides of the blade securely into the tray with the button that makes it retractable?
Mine is a couple of years old but I’ve discovered after thinking that I had bad batteries that it’s to this charger it only charges the batteries about 50% two of the green lights come on and that’s as far as it will go now I took those batteries and plug them into a separate Ryobi charger and they topped off quickly so there’s a problem inside of this has anybody seen it or heard it and what do we do to fix it I do everything but transistors and resistors
My Ryobi p125 6-port charger 18 volt lasted about 2 years then it just died. I don't know why.. I pulled the back off thinking a fuse might be blown but realize that the technical outlay of the charger was above my training. I know it has been in heavy use and I can see where it really needs to be clean ed. Could you do a video on the best way to clean one of these units. I would really appreciate it if you would, R. Prestwood
I was given this model without a power supply but I have lots of used ones. Will a DC 4.5V 600 mA power supply work? Can it be slightly higher than the required minimum?
Can the back seat be easily removed? At the back floorboard, is that where the spare tire is located and is there any space beneath the back carpet area for storage. I do very little travel besides just some local, in-town jaunts and I'd love to have one of these with the rear seat removed so I can easily haul my two dogs to the groomers. I have read that the engine life expectancy is about 200,00 miles. Is there a big difference between the S and the SE models? I have rheumatoid arthritis, so it becomes difficult for me to swing my leg up to get inside of my Ram pickup. I am looking to replace my '04 Ram 1500 and just use one of these as a used car option. Thanks for the video..
I don`t own a Nissan Cube, but would imagine it is a relatively straight forward job without any electrical connections to disconnect... Am thinking about a Scion xB, myself, & would also remove the back seat for more utility. Both the Cube & Scion are much easier to access than a large full-size pickup truck`s seat. If you plan to keep your Cube for a long time & it has a CVT transmission, CHANGE THE FLUID, FILTER & (clean) the PAN MAGNETS EVERY 20k miles, or you might face a $5k repair bill---it is the Cube`s notorious achilles heel. If you remove the Cube`s back seat, you should have a very usable 65 cubic feet of cargo space that your dogs will enjoy. Good luck !
I got no box..the box it came in was beat to hell ..under a ton of bubble rap the copter was still broke..fix and found out someone else flew it and the battery was no good...and it was the old brushed version ..was sposetoo be brushless...I made a copter of it...will run on 12 volt ..
Just wondering just bought new eneloop at 2000 mah, did test mode just to check and didn't show mah results but ah is that because display can't display four digit number over 2000
Thanks I had to watch this, to put back together mine’s. 1 question I found that if I screw it too tight I can’t push forward and retract the blade when it put back together. Is this operator error or should I leave it a bit slack and not too tight?