Yes, once you assemble it you can use it right away

Thanks! I totally missed it. I’ll put a correction in the video.

Thanks! It was fun filming the part that water sprays around, but then it was time to clean up...

Is it the step that eufy app generate a QR code for the smart lock to scan? It could be that the smart lock is not able to see the QR code well. You may try to turn the brightness of the phone up and move the phone slowly from near to far so the smart lock can see it. Or it could be that the smart lock is able to see the QR code, but the information on the QR code doesn't match what it needs. In this case, you may try long press the sync button again to re-start the sync process.

Just need to push it inside

Yah unfortunately it’s not design to hold each prices in place when you stack them up

Yah I think yours is not locked in place. Need to push it backwards till you hear or feel a click

www.amazon.com/gp/aw/d/B01N57S9O6?psc=1&ref=ppx_pop_mob_b_asin_title

These LED robes cannot be cut. I got the 6 ft ones that fit the best for my steps.

You are welcome! Glad that it’s helpful for you.

No, during the installation your phone can be connected to the 5G network. It’s just the floodlight cam itself connects to the 2.5G

@@randomhomegadgets Thank you for your reply. The 2.4Ghz requirement on the phone was always a pain.

Yes, you can use it stand alone

It’s the anti stalking function from Apple. When the tag moves along with an unknown phone, either iPhone or Android, it will make a sound because it could be some talker tagging you. I’m not sure if you can disable it though.

Did some research about it. You can try to put the tag further away from your android phone, such as in the trunk, then it won’t be close enough to trigger the alarm.

Thanks for your suggestions, I might try that but I reckon the only sure solution will be to remove the speaker if I want to use it for car security.

Check to see if you have an in-line float switch. If you have one, open it and see if there’s water backing up in there. It’s likely that the drain pipe is partially clotted and takes a longer time to clear out the water. So when water backs up to the float switch, it shuts off the AC

Thanks for your reply. I don’t have in float switch. I changed thermostat to old honeywell and all works fine. Not sure what to do.

Glad that it’s helpful for you :)

Yes you can register it with both eufy app and find my at the same time. I mostly just use find my, but for reverse find your phone then have to use the eufy app.

Thank you 😊

You're welcome! I’m glad that it’s helpful for you :)

I used the Samsung microSD card. Try to re do the formating in general-> storage. Sometimes it may take a couple tries. If still not working, check if the card is corrupted.

@@randomhomegadgets thanks!

You're welcome! I’m glad that it’s helpful for you :)

Glad you liked it!

The original one should have a layer of sealed plastic wrap. If not, should ask Amazon to replace it

Glad it was helpful for you :)

Glad it helped :)

You can try to replace the brush, but otherwise yah get a new one 😆

Glad that it’s helpful for you :)

For the wired version, will need to bypass the home chime to get enough electricity to run this doorbell. You can get the battery version then you don’t need to bypass the home chime.

If you use the deco as the router, then should turn on ip pass through. You don’t have to turn off wifi but there might be interference. If you use the deco as access point, then don’t have to turn on the ip pass through.

Yah that’s the only way since you don’t have Ethernet cable to the second floor. The speed really depends on how far away the main deco and the secondary deco. The closer the better

If you use their provided spacer it’ll be slightly easier since there is a bit more room.

You can use seat belt too, just need to thread it through the back where the belt lock is

😊

If it keeps coming on and off, it’s likely due to the consensation line not flowing well. You can check out this video on how to check the condensation line: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-AiBFL-l0uxY.htmlsi=l5dboXvqG975IsW0

Glad it was helpful!

Glad you like it :)

The Verizon 5G router has the combine function of receiving 5G cellular signal to get internet, and the router function of routing internet connection to different devices. The Deco is just a router and mesh network, but cannot receive 5G cellular signal. So you will still need to use the Verizon 5G router, you can add the Deco to make a mesh network.

Do you mean the app setup? It's showing in this video at 7:50 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2LXLKL5kU08.html

If it keeps coming on and off, it’s likely due to the consensation line not flowing well. You can check out this video on how to check the condensation line: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-AiBFL-l0uxY.htmlsi=l5dboXvqG975IsW0 Also make sure the air filters are clean.

@@randomhomegadgets Last night I went back through your diagnosis’s and it was in fact the the float switch! The drain pain underneath the unit was bone dry so I didn’t think it could be that but when opening the side panel I noticed some slight puddling inside the unit underneath the coils. Checked the float switch and as soon as I pulled it out the AC kicked on! You are a rockstar my friend 💪

If your old bell is facing straight outside then you don’t need to use the angle plate. If your old bell is facing towards the wall then you may the angle plate to tilt the camera to look outside.

Sorry, my early videos didn’t turn the background music down :(

Yes you can set up like that, but only the fist deco would have the fastest speed, the rest of them set up wirelessly would have slower speed

Yes the battery should be exactly the same

Without subscription it will still work. The subscription gives you more choices of sounds and narrated bedtime stories.

Thanks for your kind words! I’m glad that it helped you to solve the problem :)

The motor is very quiet and smooth.

@@randomhomegadgets thank you