WELCOME to Dairle Auto Classic Restoration Repair! With The Increase In The Cost Of Living. This Channel is all about Saving You 💰 Money. This Channel show Videos on "How to Repair or Replace Parts on Automotive , Commercial Vehicles , Farm Tractor Equipment and Auto Restoration 🚘 . The purpose for this Channel is to Motivate and Inspire you to do your own Auto Repairs, Restoration , Gardening and Handy Work.
ABOUT : I have over 40 years of experience in Automotive, Heavy Truck and Auto Restoration, . I began by restoring Farm Tractors and Heavy Equipment. A short time later I decided to restore Classic Muscle Cars. All work from bumper to bumper such as Upholstery, Bodywork, Painting and Vinyl Top installment. Also Engine ,Transmission and Differential Rebuild are all done in-house.
The Purpose For This Channel: "You Can Do Anything You Put Your Mind To "
Thank you that was very helpful! That last screw wasn’t as hard as I thought it would be. I was able to use a light to get a visual and that helped me then get r’ done! Great video🎉
Hey, I have a 2024 MV607 with 50k miles. It is asking for trans filter. Do I replace both filters or just the exterior with 50k miles on it? Thanks in advance
I live in Phoenix Arizona.110+ all day I mean here we are going into October it was 114 today. I am going to use the 15w 40. Unless you think I should look into getting something different.
I can not seem to find a oil change for this Hino. Have you done one yet? I have looked on your site, but yet to see one. Wondering if I have missed it. want to say Thank You so much. You have saved me soooooo much. I have just started my small business and bought this truck. All I need is the oil change.
I have a 2001 4300 it runs rough at idle and while driving. Starts fine doesn't die. Just runs rough low power. I checked and my fuel pressure is only 45psi not the 60 psi as needed. I cleaned out fuel lines back to the tank. No change Do you think it could possibly be my lift pump? Thanks
@labronragon3022 mainly on a Maxx Force. Low Fuel pressure can be cause by a clogged Fuel Filter. Or a clogged Fuel Strainer. There has been times that I had to replace the Fuel Filter Housing on some Trucks.
@labronragon3022 let that be the late thing you do. Also if you feel that is the problem. Have a diagnostic done first so you will know which one could be bad.
I'm a female who knows nothing about vehicles but can really appreciate your skill, amazing video thanks! I had my alternator replaced. The car was noisier afterward, especially when the air conditioner was on. Eventually, the a/c started blowing hot air. During an inspection of the vehicle, mainly near the front bumper, 2 bolts were missing. I have been googling trying to figure out what bolts. I suspect it's the a/c compressor bolts. Could that be why my a/c stopped working? Thanks in advance for any advice!
@vossygibson8608 First of all, I want to thank you for watching and supporting my Channel. You have asked me a very good question. It is a coincidence that all of this happened back to back. The Mechanic may have disconnected your A/C Compressor in order to replace the Alternator. If that's the case. That is not a common thing to do when replacing an Alternator. By your A/C Unit making noise. It could have been three things. 1. A/C Belt slipping ,misaligned or have something on it. 2. A/C Clutch 3. Lack of Freon It bothers me when a Mechance don't place back all the bolts that was removed. I'm sorry that you have experienced this.
My transmission is not shifting properly between 45 mph to 65 mph,it does erratic pulls and when spending up it takes so much time to reach 65 mph! An Allison Shop already changed the TCM but same results! Lost here,any thoughts?
I have a question, I hope you can help me. I have a 2003 3.2 CTS that doesn't go over 70 km/h. My mechanic suggests that I change the strainer and check the transmission, but is there anything else I can check?
@RV-in3oi That could be a number of things. As for you Transmission. Notice if it is shifting through all the gears. A clogged catalytic converter or spark plugs can cause this problem. If you have a Engine Light on. That will help to diagnostic the issue.
@@dairleautoclassicrestorati6892 Trust me (and everyone else telling you this) - you are the best source of Hino 268/338 repair videos on youtube. Thank you.
Thanks so much. First oil change on a new Transit and had a hard time identifying the drain plug. This video explained more in 10 minutes than a call to Ford Direct and a visit to the local dealership. The dealership said that Ford designs the product so you'll be compelled to return to the dealership for service? Loved the child support comment too. d
Would a leaky seal cause truck to not start after sitting overnight? After a Squirt of starting fluid it starts and runs normally. Leaking at seal between engine block and pump. When hot doesn’t leak and starts fine. Would you recommend new pump or just new seals? Thank You sir, appreciate it!
Great video! I’m experiencing this same issue. When it first began my technician thought it was a dirty cap issue so he cleaned it and replaced it with a new cap. Same problem happened so then he replaced the sensor with a new sensor. It’s still happening. What could it be??? I put new batteries couple weeks ago. Could the new batteries have caused this issue?
@GoMoLogiz I thank you for your comment! New batteries would not cause the problem. Make sure the Harness going to the Sensor is fine. Also make sure your Radiator and the Radiator Reservoir is full. Also look at your on- broad diagnostic by your left knee. And make sure you do not have to reset any type of Radiator or Coolant light.
Thanks for the reply!! Harness going to the sensor looks fine, radiator and radiator reservoir are both full and radiator or coolant light doesn’t need to be reset. The low coolant warning light doesn’t come on until I’ve drove for long periods of time. Also, I can’t seem to find any external leaks. My mechanic says that he doesn’t know what’s causing it to happen
I had a grease fitting installed on my knee, when i had a knee replacement. My first knee replacement didn't have a fitting, Since using this method, I don't squeak anymore on my knee when walking. Great tip.