Of course. The circuit is more complicated.. H-bridge ! Thanks! FF

Hi! I used this set: - Brother Laser Print DCP-1612W - photo paper for laser printers - nail polish remover - best solution: acetone 50%, water 50% Look here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ast-VMLKXJw.html Thanks! FF

Hi Ram... Use relay model TE RT314012 or any. Is ok! Thanks! FF

@@fafuclab sir but this relay is so expensive on my country and my country name is INDIA please sir send me a simple relay circuit please help me sir 🙏🙏🙏🙏🙏

Hi Ram... Find this type: - SONGLE RELAY SRD-12VDC - SONG CHUAN 507H-1AH-F-S-E 12VDC - Tear down any pcb find ? Thanks! FF

Hi Yuri! K1 and K2 = Relay model TE RT314012. (Any is ok) PCB, see my website ... fafuc.altervista.org/diy-pcb-shaker/ Thanks! FF

No problem giving you the code. If you watch the video (4:07), you find all the code to copy. With patience you can learn and understand a little more. I hope I was helpful. Good job boy! Thanks! FF

@@fafuclab tq so much sir.. i will try it. Will update later when success make it.

;)

Hi Fausto, Sorry if I only answer you today. I was off site. The tool I used is a "rodent" for sheet metal. It can be found in various online stores under the name .. - HT-204 nibbler-shear forceps - Nibbling Tool TZ-20 - Engineer Nibbling Cutter TZ-20 I hope I was helpful. I like your words of encouragement. Thanks! FF

Hi, Code: 6:55 Diagram: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-5D8swmTliTc.html Thanks! FF

👌😊

;)) Thanks! FF

E' solo un test. Comunque non si sa mai! Torna a trovarmi! Grazie, FF

E divenne "Triccheballacche".. ;)) Torna a trovarmi! Grazie, FF

Un pochino.. ;) Torna a trovarmi! Grazie, FF

Ciao Jesus, non comprendo quello che vuoi dirmi. Grazie! FF [ Google ] Hola Jesús, No entiendo lo que quieres decirme. ¡Gracias! FF

Ment so I can print /toner transfer method :)

Hi! See my website ... fafuc.altervista.org/diy-speaker-protection-soft-start-aka-antibump/ Thanks! FF

Hi! See my website ... fafuc.altervista.org/diy-pcb-shaker/ Thanks! FF

Ciao Manfred, ti ringrazio per l'utile segnalazione. Anche se sono sicuro di aver controllato molte volte, vedrò di riverificare.. "Devo solo ritrovare il pcb originale..". Punti interessanti: 00:41: pcb originale (D1 e D2 invertiti, collegamento anodo/catodo). 02:49: pcb nuovo (D1 e D2 speculari, collegamento anodo/catodo). 02:49: pcb nuovo, stesura (DZ1 e C6, polarità sbagliata). 02:56: pcb nuovo, fase finale (DZ1 e C6, polarità corretta). Torna a trovarmi, grazie! FF

Part1, Part2 and Part3 (C code) ;)) Thanks! FF

;)) Thanks! FF

;)) Follow me, thanks! FF

Hi! Write to me. FF

Hi! Write to me. FF

Sir this curcuit is Sterio or mono????

Hi! Mono, Stereo, Both (Just swap/replace relays) Thank you! FF

;)) Grazie FF

No special relay, any is ok. FF

Hi! I used this set - track: 1,5 mm - pad round: 2,5 mm and 2,8 mm - pad rectangle: 3 x 1,5 mm FF

Acetone only, not mixed with anything else. I'm glad it helped you. If you want, share the video. Thanks! FF

@@fafuclab Of course! I going to share with many others!!

;)) Thanks!

I saw you solved. Great! FF

Thanks! FF

Noooooooooooo! I didn't notice the section of the wires! Thanks so much! FF