This Channel talks about 3d printers mostly and their features. Sometimes a throw a wrench in the engine and post a car fixing video or a review that has nothing to do with 3d printing, because Some things need to be shared with others that may need answers on a particular question. If you can stomach this type of format, throw me a like or a subscribe. I am focused on quantity rather than quality at the moment for improving my video making skills. I see some being displeased because I speak on features of 3D printers I only see on pictures, but I could not afford to buy them all. So see ya around!
Jewelery is usually carefully handled, is not like patching a pipe which flexes constantly. But yea it depends on many factors how well they bond. I had mixed resilts with both brands on the same application. I glued the same application hundreds of times, and i had 30 40% failures wth both brands. Others have experienced the exact same issues i got. The epoxy became like cartilage soft in some instnces. And others became very hard. So i think is the quality or temperature amd humidity.
I think you should demonstrate EVERYTHING from now on! This is the clearest instructional video I have ever seen... Full of detail and great tips. Love it! Thank you so much 👏 👏 👏 👏 😊
I have not looked into the settings that deep. I am not sure how i could do that. This drobo is quite old. It is probably 10yo. Not sure if the new firmware can improve and add more features to it.
@@RoamingInterests Thank you for the reply. Within the Drobo Dashboard GUI (I'm using version 2.6.4) go to "All Drobos" then go to "Capacity" then click on the icon on the top right to switch from pie graph showing "capacity" to instead display "usage" then look at what is being "used for protection" (shown in orange color) this will give you a clue whether you are using single or dual disk redundancy setup.
Others have probably said it already but, microstpping! Yes, most cheap printers are running 32 bit, but many of these are still running older Marlin firmware and can't do more than 16x microstepping. (Microstepping is a way of using PWM to simulate out of phase sawtooth waves on each phase, giving a changing balance between the fields on each motor phase. So, when a modern firmware like Klipper is run on a fast, modern contol board, you can easily get high degrees of microstepping, up to 32x. Or, 32 microsteps x 200 mechanical steps equals 64000 steps. That's ridiculously high precision, considering most crummy old bedslingers are running at 400 or 800 motor steps per mm. Oveersimplified, yes, but with Creality's lower end, churning out cheaper and cheaper enders, that's "low precision" by today's standards. And yes, I know, Creality are also moving into enclosed corexy, but that's their high precision sector.
Your video is a joke, you have no clue how to present a fix . You spent 10 mins showing you could not remove it. You’re a hack. Took mine out in 7 mins.
Actually when it comes to fixing cars or presenting things I am a hack. that is why my channel doesn't do millions a views. I don't present myself like the purveyor of truth and fixes.
Took less than a hr to remove mine. I read it took some 3 days and im very sick.. im thankful. Tomorrow i will put part in because it comes in between 1 and 3
Yea we did not know how to put it in and what else to take apart. We used a bit of brute force to fot in the new one. Checl out the comments and the second video it may have some tips. Some have commented that the exhaust needs to be taken out. I guess there is more ways to skin the cat.
@RoamingInterests I'm paying for it. Lights make me sick and attack my nervous system. I'm in pain just had no choice.. Maybe I can take enough meds to finish. Very dumb what I'm doing just had no choice 🙃
The sun and lights and environmental factors just it's like I'm allergic to the sun like a vampire in a way but dark at night can hurt me too it's electromagnetic I'm sensitive too. It can kill me. I just don't have help really and have to do and I'm very sick just not like others know when I'm working on it I hide it and suffer. I get home health though. I am 33 now. There is no kindness in this world or a hand or anything. I think mine is front wheel bearings at this point. I do wish I had a hand but that turns to begging. People one day will see for themselves how people are. I'm basically going outside and doing it because I don't have options but do what I have to do but it can kill me also paralyze me it affects my body so bad that I am working on a dumb car that in the end I wouldn't be able to possibly drive because it's affecting my body. Nights are better though still . I tryied a go fund me www.gofundme.com/f/support-needed-for-hcp-patients-car-repair I tryied everything I could just maybe if I take my scrapbook to a mechanic shop family owned and show them the stuff my diagnosis and stuff maybe they will be kind and give me a good deal.. I live in Texas. I wish I had kindness and a hand and I wad kind to many and helped people just sometimes it don't ever come back. I think about giving up each day and what I'd do would be hang myself just it's easier and way to easy to do I almost did it checking to see if the door could hold me and I almost fainted not trying I was just preparing for a option as that is a option just I don't have many options in my position and drs know I tell them people know im honest but in the end it's just very had in my position and people with lupus say I have it worse but it is similar to it. I almost died 2 yrs ago I fought to be here and I suffer here. I am a big believer in God and I pray he handles it 🙏.. It's rare what I deal with not many would understand or the rest I guess it matters who a person is status wise but they know what they did too. Wild world..
I have seen some documentary on electromagnetic sensitivity. There is Radio Quiet Zone in the US where is radio and wifi free. Maybe you should visit there, take a vacation there and see how you feel for a few days, there are a few people living there specifically because of their EMF sensitivity. The NRQZ is centered between the Green Bank Observatory in Green Bank, West Virginia, and Sugar Grove Station in Sugar Grove, West Virginia. Have you had any doctors corroborating your problems and see if you qualify for some governmental help? I checked your diagnosis and what you explained. I got the wrong impression that you may be sensitive to EMF. But i misunderstood. Could it be that you may also have EMF sensitivity? I am not an MD and I may be completely wrong. Here, but if you have two comorbidities, the symptoms of one may mask the second one. Again I am not an MD. So take my ideas with very large grain of salt. Also you need to publish that page on GoFund me on social media, your friends need top know of it. As for your dark thoughts I don't know how to handle it. But you may need to speak with someone more qualified than me. See I am passing the buck here, which is not cool of me, because you are in pain. But you see, Doctors really know how to handle sensitive issues, and I am afraid I may say the wrong thing and do more damage than good.
@@RoamingInterests de fapt, noi romanii avem un non-accent, o lipsa a lui, dar un anume mod de a rosti mai ales consoanele, clar si apasat, in loc de estompat. Uite, francezii, spaniolii si italienii au accente super tari, ii recunosti a mile away, francezii chiar parca transforma engleza in franceza cand vorbesc. PS and since you are putting out content on sand filter pumps, I was curious on one item: do you keep the same initial batch of sand throughout the summer season and only apply backwash/rinse or do you change the sand during that interval? Many thanks for the content, man!
Yea sorry i am late to give you an answer. But usually the bags of sand tell you how often to change it. But I have a video where I cleaned the 10" sand filter and I found a lot of small twigs and debris in there and there was a fish like smell. So depending on the sand filter size I think on the large 16 inch pump with a Leaf trap you should change it every 5 years, i may be wrong on that. But when you winterize your pool you should clean the sand filter of debris that makes it past the leaf trap. Beware of the smell when you open it up. Yea I make all kinds of content. I guess I get bored, and I don't have too much to say about Pools, or 3d printer or, anything, Maybe i should become another podcaster. Thanks for writing here. cleaning the sand filter: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2QPgcXfN6HQ.html and thins is my gardening video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-9eO_DMHCgxs.html
I havent used the JB clear weld yet but Ive used gorilla epoxy and it seems to have a rubbery feel to it sometimes even after it hardens completely but I didnt like it as much as the Devcon line of epoxy products, their epoxy like the 2-ton one for example isnt rated as high when it comes to strength and how much psi it can endure but it became solid and didnt seem like hardened rubber, and that rubber-like composition is probably the only reason gorilla is rated to endure such high psi, devcon may actually be more solid just might crack/break easier. I want to try oil based spray polyurethane from minwax. Fingernail polish works decent for coating 3d prints as it seems to soak in and fill voids very well and gets really hard but you have to sand it smooth between coats and then may want to paint or whatever over it, to hide it lol 😅
once every two years. But I have a video cleaning it and within a month there was large debris in the sand tank. And you could open it up at the end of the season and take the large debris out. or now if you had it for a while, in my video this debris accumulated in a month or so.
YEa now is clear much more clear - but this ran for 7 days and even today is still live streaming on multiple channels on youtube and finally someone else has posted a video about it. all the noise makers about BTC halving didn't see this for 6 days.
4 месяца назад
Thanks for the Video. Just encountered the Same issue. Did you had to flash the firmware after replacing the card?
Now just imagine the Egyptians did this with 60 tons plus and moved them hundreds of miles and then lifted them 400 feet in the area. They also didn't have any of the tools you had.
I don't think Egyptians were simple. they did calculations in binary, they had knowledge end engineers. Now there is an emerging hypothesis to say that some of the Egyptian monuments or pottery that is machined was inherited from the Atlanteans. And the dates of the great sphinx coincides with 12 600 years ago. More and more scientific data comes out that there was heavy bombardment and biblical floods that brought humanity to the brink of extinction.
@@RoamingInterests i got synology because they had the same hybrid raid system where u can have different sized disks and get more out of them than a normal raid only issue is that almost all synologies have a volume limit of 108, thats not as bad as the drobo 16TB which is very ouddated by todays standard but still
Thanks. Those ancient aliens folks are in it for the money. As long as the history channel gains audience, the propagandists of Ancient Aliens Theorists make money, so they have a financial incentive to cast doubt over who built what. Now I have seen archaeologists expressing that it is racist to claim that all the monuments of Europe were built by Europeans, Meaning that th ancient Aliens Theorists don't make any claims of aliens building those in Europe. But all other ones all over the world must've been built by aliens. Seems easy enough to call the people racist nowadays. A new voice has emerged Matias Destefano claiming that he remembers past lives and that in Atlantean times there were four guilds, air, water fire and earth. And the water was enchanted in hymn and would cut the stones. Now this is beautiful as a story but until there is more definite proof of that, and the scrolls of Ancient Kemet old name for Egypt a province of Atlantis from the Hall of Records under the Great Sphinx (purportedly) in Egypt aren't unearthed, it remains as a beautiful tale. Until then I'll hold as truthful Jean-Pierre Houdin's theory of an internal spiral ramp. Even so the precise cutting of the stones still does not explain how they were cut with such precision. In addition the adjacent stone walls faces are not prefect planes they curve but the face walls of adjacent stones butt together perfectly. Today, with CNC machining as an experiment we can attempt such a feat, not sure we may succeed. So that is why a beautiful tale as Matias DeStefano's is gaining traction.
Very clever to use a jack as a form of levering tool. Not exactly full on ancient methods, but very much in the spirit of them. When the rocks become too heavy for the muscles, they aren't too heavy for the brain :)
Thanks. If you need deburring on the inside of a hole, the spinning action is helpful. But if you need it on the outside is not that helpful. Also this idea was more for plastic where the skipping action of the deburring can leave rough edges that scratch. With the non spin you have more control with plastic.
I compared JBL Xtreme 3 to JBL Charge 4 and the Xtreme 3 sounds very underwhelming at low volumes. I like the tuning of the Xtreme 3, but Charge 4 sounded louder. The low volume is very off-putting - you'd expect bigger sound out of such a big speaker - only that makes the tradeoff in terms of portability worth it.
I still like the xtreme 3. Never troed the charge 4. But the bose sounded quite loud but the bass is quite deep and ample. In my experiment the boombox had an even loude and deeper tones, and very clear. I felt that the xtreme was quite good. I will perhaps in the future look at the charge 4. But just loud doesnt cut it for me. It has to have clarity and deep bass.
Every company is capable of making a bad product and it unfortunately can leave a bad taste in our mouths but it’s important to realize that same company can make good products also. It demonstrates how important testing is.
Perhaps they would, but I have no way of making those strips of metal currently. I think I would need to bend them and I do not have yet that capability. With 3d printing I was able to whip up the bracket much easier and somewhat quite precise. I saw in the recording where the cutting tool got loose and now I know to check the 4 nuts on the bolts. to make sure is tighter. I also saw on a blog that applying too much pressure I could damage the bronze bearings on the head stock. So I have to keep that in mind too, in my quest for more rigid tools. But I alreaady made a new part to attempt to see if a boring bar will stay rigid enough. The last blue piece was ABS made and ABS is so difficult to finish printing without it coming unglued from the bd, that I made it in PETG, which has some flex to it. I may post another video soon.
Good Idea. Drill and drill bits. I happen to have those. So you mean something like a good chunk of metal drill it in a square pattern where the cutting tools would slide in, hack saw the holes, file them, and then make the four holes to connect it to the cross slide and then tap the holes on top to bolt the cutting tools down and then we're done?
@@RoamingInterestsI do not think you need anything that elaborate. Just a steel plate with four holes for the T-nut bolts. The plate it self would press down on the tool. If you want something similar to your 3D printed design just make this plate with additional two holes with threads. Than use standoffs for the T-nut bolts so it sits a little higher so you can slide the tool in without loosening the T-nut bolts. The standoffs you can make on the lathe or you could just use regular nuts to prop the plate higher.
Thank you for your research and for sharing. Question. When you're zooming in on the 0.1mm drill bit are you moving the magnifier closer or zooming in with the camera? My olden eyes no longer focus like a camera can, so I prefer 20X magnification on the entire diameter of the magnifier instead of the 20X being ONLY in the coin size magnifier. Do you think I can find a magnifier that will do what I need? Thank you again.
I don't think you 2ill find a magnifier like that. I also think that the magnification that is advertised by these companies is quite stretched from the truth.
Tengo una impresora cr10 s5 Creality y tengo problema con el eje Y, el motor algunas veces esta imprimiendo y empieza a atascarse, como si no pudiera girar y estuviera trabado, al principio pense que era el motor, lo reemplace y el problema seguia, le quite la correa por que pense que tal vez eran las excentricas que estuvieran dañadas y el problema persiste, parece como si el motor estuviera atascado y se estuviera forzando aunque ya no hay nada que impida que gire, esto lo noto al tratar de mover el eje Y en la consola, sabrias que es lo que esta dañado, gracias.
I have pinned a comment that explains how you can slide it in. You have to pry it from the side. In the comments there are bits of information that will help you. also there are two videos describing the work done. however the camera wasn't rolling when we slid it in. this wasn't done intentionally.
Intex has great customer service. I ordered a pump off amazon, a piece later broke a few months after ordering. I contacted the company, all they asked for is a few questions & a picture of the order. They sent out the piece completely free.
@@RoamingInterests I googled the Intex co. Went on their official site “intexcorp” then I scrolled all the way down to where it says “contact us.” I’ve done it a few times & they always helped me as long as it’s during business hours.
easiest way is remove the mount. lower trans. remove exhaust. remove passenger side manifold. and every hardware bolt on the trans on the passenger side. i used a big bar a small 2x4 and wedged it in bettween the traany and passenger side. it was plenty room.
When you say remove the mount are you referring to the transmission mount that has the 8 bolts? I have been trying to get the shaft back into place for days now and no luck
I have a 15x48 intex and just purchased the sx2100 sand filter does anyone on here know if I’m gonna need to get additional adapter fittings and if so which ones ?
I don't know. I didn't need additional cpmnectors when i got the 10 inch pump. However. The pump from intex does not come with the 1.25 inch hoses, only yhe pool comes with those. In my experience of onstalling one pool and 3 pumps.
