Yes i know i had to check everything for the video. But I didn't have much time to shoot a video, and I wanted to show only the main thing, how to quickly disassemble and test all 18650 banks. There were a lot of bad ones, they sat at 0 without recovery, so there was no point in shooting a lot. I use such old 18650 banks in my projects and homemade Power Banks.
@Robotics_Robot me too, i mainly buy used battery packs from local scrap company. Sometimes only 2 was bad in pack, but in majority of situations always is 50%50%. Of 100 in pack 50 are bad ( bad IR or on 0V ) also using it im my DIY. Greets
I do appreciate you showing off the new tool....but with no actual speech it's not really a review and it was never actually used for its intended purpose.
Hello! Thank you for your comment. The tool is new so it was just a quick unboxing and review, I haven't worked with it yet. And without language, because there is an accent, I'm improving my videos little by little.
Hello! Yes, I was in a hurry and didn't have time to film everything at once. I will film the 3rd video review of this engine, in which I will completely disassemble and study it. This engine is very interesting, it is a legend. Regarding starting, I did not start it, I read a lot about it. This engine requires special fuel, and I do not have such components now.
Hi! What type of DC motor do you mean? There are two, I didn't measure the shafts, maybe 0.5mm. I need to measure them accurately. I just don't have a spare DC motor to measure.
Hi! I think it will work. The board has proven itself well in my projects. It gives good current and voltage. I don't know about interference, I haven't checked it
@@Robotics_Robot he is asking what the torque is, its very hard to figure it out as they all list it at 10kg/cm online but it doesnt make sense that they would all have the same torque when they have different gear ratios
@@janramonmartin Hi! Yes, they all have different torque. But the power is the same. For example, a 120 rpm gearbox will lift 1 kg. faster than a 12 rpm gearbox. They are very powerful! Depends on what projects you use it for.
@@Robotics_Robot yes I found a spec sheet in the end, apparently it has 70nm torque at 12rpm which is very powerful, would probably destroy the gears if you actually tried
Hi, i wanted to buy the 12V, 80RPM version of that motor. On the website i see a no load current of 0.3A just as your, a load current of 1.6A and a stall current of 6.5A. I was hesitating between using a 8A power supply or 10A power supply. Btw i want to use the motor with a load that's why i'm targeting for higher current ones. Can you help me to choose one or maybe something else?
Hi! Yes, the black motors have proven themselves well. I think they can be used in your projects. You just need to know what voltage you will have and what gearbox you need for the speed in the project. And you are done!
@@Shruthi-op7ji Hello! I did the project a long time ago. There is a normal code. You can find a sample code in the comment below my other video. L298 driver. They are similar.
Nice wrench, very nice. Love the head stop on the open end; some ratchet wrenches I bought have a stop integrated in the 12 pt forging. Another 'travel set' of dbl end ratchets I bought have a stop forged in the middle, by way of stamping 14mm on one side & 12mm on the other. Only need ½ the wrenches w/ you. Being different sizes on either end, makes it ¼ of the wrenches. Then you get somewhere & need an open end! LOL I do like the Joker... but, I'm so-so on no reverse lever for the ratchet. Had no lever for 40+ yrs & a lever for 2 yrs; haven't decided, yet.
Hi may i ask how can i connect 3axis joystick potentiometer in dc motor with dc driver? i want to controll the reverse and forward with joystick, can you help me with the wiring diagram?thank you 🙂
@@coolkalangjack If you want to connect to exactly the same driver as in the video. It's unlikely that you will succeed. The joystick has a potentiometer in the middle with the value set to the middle value. And the potentiometer has values from 0 and above. The engine will start from the center position. If you do this on an Arduino, it can be removed programmatically. And if it’s the way you want, I don’t know. There, then the joystick needs to be disassembled and the springs removed so that it is from the zero position, and not the central one. And reverse will still work on the buttons. If I have time, I might make a video on this project. I will try.
@@Robotics_Robot thanks because in my country its important to have atlest 1inch or more for splicing and then using Electrical tape, but since it can be remove i might buy one for work thanks for the info xd
@@musichead4555 There the latch is pressed with your fingers and adjusted to the desired distance. But if you press harder with your finger and pull down, the latch can be removed and put back on if necessary.
Hello! There are a lot of setup videos on the Internet. You need to short-circuit the probes and adjust the desired voltage and current. Each model has its own settings.
I just finished a low speed hand held 2" wide belt sander using that black 24v 120 rpm motor. Quiet and power full motor. But i just ordered a new same motor with 480 rpm as 120 rpm seems very slow for that purpose. I actually made same project using the silver colour (12volts 480 rpm) motor as shown but it a noisy motor and become hot to touch after using it around 10-20 minutes. Worse, the gears went kaput after a used it for a while. Not very robust gear for a heavy loads but the motor seems fine.
Hello! Yes, black engines are reliable and expensive. And whites sometimes have problems with the gearbox. You can take a black motor with high speeds, and put adapters with large gears on it to raise the speed even more. The principle is like riding a bicycle.
Yes, you can, but you just need to connect everything to USB. There it produces from 5 volts to 3 amps. It seems to me that it’s easier for you to choose ready-made USB chargers that have 12 Volts or higher at the input, and a stable 5 Volts at the output.
Sorry, this was done a long time ago, there is no code. You can find the code in my previous video. Driver l298t for Proteus. The code there is the same, only slightly modified for 2 drivers.
Потрібна роз'яснювальна бригада)) Я вставив 4 акумулятори AAA (про те що будь-якою стороною я зрозумів). Щось щось треба робити, регулювати? Вони ж самі перестануть заряджатись, не вибухнуть? Можна на ніч залишити?))
The lower holder is always a minus of the battery. It is necessary to set the type of charge, charge or discharge of the battery. If you charge 4 at once, they heat up, then they should turn off. But it is better to watch this technique!
You can simultaneously charge 4 batteries with a current of 500 milliamps, the main thing is to use charging no more than 2 amperes. Otherwise it may burn.
Hello! Universal pliers. They can be used to press the tightening clamps, and it is convenient to remove various parts, this is my personal experience when working.
I purchased this but I am having issues with power supplies. If I use a high power USB-C supply, eg 60W one, it does not even turn on, nothing. I cant use a 30W 5V either. Only seems to work with standard low power USB-C chargers eg 15W ones. Any thoughts on that?
Hello! Yes, LiitoKala Lii M4S is a good and technologically advanced charger for 18650 batteries at the moment. But for its long-term operation, you need to use a 5 V charger with a current of no more than 2 amperes. Otherwise, when distributing currents to charge several batteries, it will become very hot and may burn out. For good operation of LiitoKala Lii M4S, a 5V 2A power supply is sufficient.
Evet 5 v 2 amper yeterli daha değişken cihazlarla besleyebilmek için hazır modüller var 30 veya 50 volt giriş ve 5v 3 a veya 2 amper çıkışlı onlardan alıp modifiye edebilirsin ben yapıcam en azından istediğim adaptöre takarım tabii bir adet ekstradan yuvarlak üniversal girişte eklemek lazım yani herşey mümkün😉
Thanks for the comment! At the end of the video I removed the music, original sounds are heard. Previously, I made a video without music and people wrote to me asking me to put on music.
Hello! They have a slight difference. The lii4s have a touchscreen control panel, a better display and can simultaneously charge multiple batteries with high current.
the m4s are more advance than the m4 it has discharged function the m4 has no discharge it also has a storage function i use this function to store my not commonly used 18640/21700 cell =it charge/dischage the battery to nominal voltage 3.7v automatic
@@KULAS6463 Owh... That Was A Great Function... It Can Prevent The Battery From Damaged... Actually, I Have Many Unused Flashlight, But I Have No Choice, I Need To Used Them Even It Is Not Needed... Because I Worry That The Battery Will Damaged If Im Not Using It For A Long Time... By This Storage Function, I Thinks I Will Not Needed To Always Check My Unused Battery For Many Times... Thanks Ya For The Information...😊🙏
Yes, this is the beginning of the game world. And a very technologically advanced engineering solution of that time. It is compact, glitch-free, and energy efficient. Thanks for the comment.
I myself spent a lot of time playing it. Tetris is a story like a dandy. Glad you liked my video. When I restored this console, it was very broken, because it was original at that time. But I knew that people would remember, each their own cool moments, about this legend of the gaming world.
Ohh my god I remember I had this thing one time my family went to Mexico they bought it for me in a market I think it was like transparent blue or something and I remember I had no fucking clue how to play any of the games or how to switch anything so it was just like playing with a calculator and I think I lost it somewhere in public fucking insane. thank you for reminding me :)
