so you jumped him 3x on a roll when he wasnt ready no doubt in my mind you can pull him on a roll. But go from a dig and I get you get walk by bus to 150mph

Thank you.

Is it safe to replace this part DIY, or do you need someone to drain the Air Con gas (freon) out before doing this?

Dusty under that hood

so, just skipped the poly-fill inside the enclosure? I'm sure blocking off all those holes helps, but probably should have stuffed the box with poly while doing the job.

My 2014 R8 a/c stopped working while I was on a road trip. We had to drive 3 hours in 90+ degree heat. After watching this video, I replaced my sensor and my a/c is blowing cold again. The differences I experienced, was the part size, mines was 15/16 not 17mm

pro tip: start the motor

can you post a video on how to add freon (charge) to the Audi R8

thanks for going to the trouble of posting this! had the same issue, previous switch installed on my 2008 was the new design though but obviously an unmarked generic ebay special so i’d recommend going genuine if you’re going to tho trouble as the non genuine also failed. Also mine did not lose any gas so was just a faulty non leaking switch. swapped the switch and all done 👍 thx again

Lmfao it worked on my 2022 premium hahah unbelievable lmfao didn’t know it could do this Lmfao wooohoooo

Worked like a charm. Thank you

Bro you have Instagram bro

Supra simple to do 😄

Ok Help me. Did you take all the freon out and then add it back to 650 grams? Is that what you said???

Great job...thank you

Good video thanks. bad music 👎

Where is the high side and low side ports?

This is the best video and thank you so much👍🏼

Works, thanks!

A question bro

Nice... Thanks it worked for me 👍

Didnt work

Thank you for making this lol I had no idea how to connect it to my supra😂

I need help please

Do you have Instagram

pressure sensor in my case, spot on. this video helped me fix it, many thanks. 2009 R8 V10

Hello, I was wondering if you remove the ppf, would it be a glue residual left on the screen?

Do you have Instagram

What does turning off the surround do? Is it only needed to uncheck if doing the DIY?

Hi what’s the wrench called?

Do you have instagram

did your compresor started doing a metallic noise and then stopped working? that happened in mine

Hi, do you have the link where you bought the part please ? (Is it the pressure sensor?)

Thanks for sharing dude!

How does it sound afterwards??

Did you do the baffling material inside the enclosures?

I eliminate the old subs built a piece on top of the semi circle and put amp change doors speakers and tweeters build a box with two 10ins sub next to old set up.eq in glove box .sounds up up up .feal the punch.

OK COOL

Where did you use the speaker wadding?

Thanknyou for this. Where did you get materials from?

Thanks for the video, makes it easier to follow! I did it make a big difference with the rattling and sound? Does it hit a lot harder than before? Thank you!

Was yours the original black one ? Or is that a completely different person?

can you film how it sounds after?

Nice job Lu Weez...Here is a link to the original write up I posted on the forum which also has links to materials needed for this project... www.supramkv.com/threads/how-to-improve-oe-subwoofer-quality-and-eliminate-vibrations.5092/

Can you link the materials you purchased here? Thank you!

Great video! It helps to see it in action. I’m waiting for one more piece to arrive then I can do this. I can’t wait!

Awesome that you did this for the community, thanks fam!

What a garbage vid....cool LED app on your phone, Chet....where tf are the pulls??? 🗑🗑🗑🗑🗑

Keep the heat coming

stolen integra car