Thanks man I do not know how my settings got screwed up but my throttle wouldn't even work I set just about everything to what you set them to thank you very much💥💥🍔🍻🐿️
hello, can you please advise me about the cruise control, I have this type of display on my e-bike and in the settings of program 16 I have it set to 0, but the cruise control does not work for me, did the cruise control work on your bike, or does it have to be activated somehow?
Hello, how are you, I have the same ebike but when I install the accelerator and set the p10 to 1 so that it works with the manual accelerator, it tells me error 08. How can I unlock it so that it works with the manual accelerator?
Hi how are you doing, i have a question, do you any idea if the display has a setting to turn itself off so the battery doesn't completely discharge? My father was using my bike and he said it suddenly turned off by itself, but he said the display showed there was some battery left (two bars). So i don't know if it turned off because it runned out of battery completely (the manual advises to NEVER let that happen because it damages the battery) or if it was turned off by itself. Thank you.
Excellent description. I can't set the speed or power for each individual assistance level. Already from level 1 the ebike reaches 20 km/h. Can you help me?
Very well done. I’m taking on a job with these cards on 21i controls at a new job a few times a day. Quick transfers helps a lot. The prefix use is finally clicking with me. F & O. Then I can focus on the setups.
Thank you. I never use PAS and want it always 0 (clumsy feet). I want the throttle to always allow full power. A PDF explaining all settings would be appreciated.
En las palancas del freno ay tornillo en el medio aprieta los un poquito lo que pasa que ay un imán y al separarse mucho pone eso E2 o Revisa las pastillas del freno a lo mejor ya están gastadas eso me sucedió a mi
thank you very much brother. you save my life by sharing this video. i bought a used bike and it has exactly same controller, i messed up settings accidentally and the bike is not starting now. I can just go to default settings with this video. thanks a ton.
i have the same lcd but it shows a error meassage E 09 , do you mabay know what this means and what part(s) i need to replace , i have been looking all day for the answer
Hi there I found this online: The electric bike error code 9 refers to the minimum one phase wire of the motor that has been damaged or disconnected But I'm not sure so I suggest you to look carefully online. Sorry I can't help you more
Got some 411 you need to know about. To start #3 if you put it on 36 which is default will give you a FALSE reading it will show you full bars if you put it on 48 will give Accurate reading. The other is #8 Which is speed if you put it on a 100 you will drain your battery faster I dropped mine down to 80 And The only difference is on 1st gear you don't start fast but what it does it gives you the same speed eat without draining your battery faster You may lose a little speed but not much But if you do keep it on a 100 you will drain your battery faster
You did a great job thank you I got my bike back By the way I also have bad knees My left knee has been opened up 10 times maybe 11 Sylvia I have mobility issues but again thank you for your video have a great day
Does it cope well on steep hills? I have a few 30ish degree hills on my route home from work that my current, smaller ebike struggles with and am contemplating buying this one as an upgrade.
@@gulfbreezr I only upped it by a couple but didn't notice any changes in performance, I didn't go too high because you really don't wanna pull more amps than what the battery can provide.
, the bms on the battery should only allow you to pull so many amps from the battery so if your instructing your controller to pull more amps than the battery/bms can discharge then you run the risk of potentially damaging your battery or bms