wow just fixed my issue with the same vehicle iv spent 1000 trying to fix it and it was just a wire shorting out. appreciate all the help

Put a pull length pipe all most same size as the cam put cam caps on and lift off ?

My blower is going on in about 3 minutes after star the vehicle So as you say I need to change the blower and the resistant

Thanks Really helpful Saludos desde Culiacán

Very well done thanks

I have my Accord headed to the doctor tomorrow. Turned the key and nothing happens. Was doing the same thing. Wouldn’t start every so often. Wait 10-30s before starting. Finally died. Like flicking a light switch with a dead bulb

Best video I have ever seen

I got a system too lean blank 1 check engine light a month later which was yesterday after installing my cold air AEM intake on my 2021 SE pilot and I’m pretty sure it’s because of a vacuum leak. Just don’t know how to find it

What happens if you only have 3 wires?

Yr the best forever

ive done that air intake seals all coils all plugs mas sensor etc still gettin misfire codes and stumbles but only when driving and those gaskets are made to remove and put back on so wouldnt have had to chareg the customer for new gasket ... Hopefully we get ours figured out im a 30 year retired tech and its starting to irriatate me lol

Broo i thought youd show me how to get that other stuff off not about your wedding lol

Hi Matt, i know you from Jay's channel lol, looks like you have a cool 57 build goiing on there, looking forward to seeing more 👍🏆.

whats the spark plug size for this year?

You're lucky . You have room to twist it more than 20 degrees AND nothing above you. I used lock jaw pliers and still no luck. Will be working on this one for the next couple of hours, I'm sure. By the time I am finished it's gonna be one ugly chewed up coil pack.

Just yesterday, also in Boise, ID. I had to repair my 94 Chevy K1500 heater hose at the manifold. I bought this truck in 2007. Then it had a whole new cooling system. Well yesterday, I got lucky. The previous owner did me a solid and replaced the quick disconnect fitting with a 1/2' thd x 5/8" chrome barb. I was dreading having to atand on the ladder hunched over cutting this fitting out lol.

Hell yea helped a lot I just broke mine thanks for the tutorial I’m RU-vid certified man💯💯🔥😂

Awesome video👍👍👍👍

A mi no m funciono x q sera 😲

So, the condenser in the front and the radiator at the end?

What size bolt is that inside the bracket

Do you have a messenger I can send a video on? I wanted to ask you a question on it, I’m also in Nampa, let me know.

I need some insight on a 2003 water pump replacement

So I am working on taking my Dads F250 water pump off. And I removed the bolts holding the dang bracket on yet the bracket won't move. What bolt/s am I missing?

Any idea where to buy extended wheel studs??

Hey matt can you tell me what city are you located at

September 2024 in Texas is very hot! My 2015 Toyota Tacoma, AC is cold on the far left driver side vent, the two on the far right passenger side are blowing hot air. Two different mechanics could not figure this fix. Any ideas???

Did anyone have the tourqe specs for all the cam gears an tensioners ? Just went through an done all this but cant find those specs to tourqe up.the bolts

👍

How do you get spark plug #6 out on a ford ranger 4.0 ?

Fuel pressure gauge first folks after checking for codes

Had 3 y blocks that is a common problem. Use a stud with structural epoxy 3M it water and oil resistant the paint has absolutely nothing to do with sealing. If it not sealing it the intake that needs resurfaced plain and simple

What about the piston is the cylinder ok

I just pulled my egr pipe and cooler and intake in 2018 Prius and was clean as a whistle. Must have changed the design for gen 4 Also 105k miles and not a single mechanical issue

Learned a lot from you and your videos- Thx!! Did the bottom end and head already. Gonna put the head on tomorrow, and try to get this thing together and running.. "HOPEFULLY" Lol

Great video, my van is doing the same where can i get the part, tyvm

And this is why I am replacing the pcv hose connector in 2012 forester In October.

Having trouble with my radiator heater control valve it cracked after I put a new battery in smh and they are hard to find

About to give these steps a whirl on my 03' Ram 1500. Thanks a ton!

Is there a final part to this series? I know video 4 years old so im sorry for late comment haha

Great video but stop yelling at me 😆

He gave up on that timing cover and scrapped it

I have 1996 xl ford f150 5.0 v8 efi got new spark plugs, ignition coil , relays , fuel regulator. Some days it’ll crank an run fine after driving it next day itll turn over but won’t start up, idk what it could be bad fuel pump or starter ?

Can this be done without disassembling the whole side and top of the engine? What if after install you just manually rotate the engine to avoid that initial slap?

Thank you for this! Now, I can get mine out of the 2.4 version finally.

Kinda. Low torque spec.

ty

Hey Matt.. I'm looking for part 1, I'm not wanting to search through all your videos to find it... I've actually got a water pump to start working on lol. Also, what engine is this? I guess i want paying attention to see if i could figure out with the looks of it, but I'm working on my v6 2.8l. am i watching the right vid? Thanks, also i appreciate your videos.. Your very well spoken & so far seem to be a great teacher. Keep it up ! 😊

Right on! I’m replacing the fuel pump in my 2000 accent and I was having trouble taking the assembly apart since I also went the cheaper way of buying the pump without the rest of the assembly. Awesome video! Thank you for making my life way easier!🤩🥳

Thank you, I learned a lot!