Color flow, NEO pixel, Addressable LEDs, whatever you wanna call it our goal is to bring you the best of it in one place. With tips and tricks for diy front and tail lights, like how to add led strips to headlights, we show you how to do your own custom lights the right way.
would this allow for 2 separate switches and a single output to device like listed below? - switch 1 on, switch 2 off = led on switch 1 off, switch 2 on = led on switch 1 on, switch 2 on = led on switch 1 off, switch 2 off = led off currently using a 5 pin 87a relay in conjunction with a standard 4 pin relay [relay 2]. where both the 87a and 4 pin relays outputs pigtail together to turn on the light while preventing backfeed power to one another. 87a relay is energized by activation of switch 1, allowing the light to turn on, while also breaking the circuit to relay 2 that is energized by this 87a relay being in an off state. when the 87a relay is in this off state, the second switch can be used to complete the circuit in relay 2 turning the light on. Its a bit of a strange workaround compared to using a y splitter with diodes coming from the 2 switches but diodes have voltage drop so not as bright. if the module shown can achieve the same that would be awesome as its a lot less wire and simplifies it down significantly since there are 4 lights in total being controlled with this 2 relay setup lol.
Too bad idk how to solder lol..U should make a premade set of these strips for this application so all folks gotta do is drop them in...I woulda used the Side Emitting Strips
i got a 09 ford focus and when i turned on the low beam they work but as u said in the vid the highbeam just turns the whole thing off will this fix it? just cant find anywhere for anything about the time of highbeam whether its negative or positive switched thanks
I don't know about you but I have my spot lights scheduled through the app. "Automation" Comes on 25 min after sunset, then after a few hours it dims to 20% and I have it turn off 30 min before sunrise. But for whatever reason they shut off at 1am and obviously do not have it set to that. Any recommendations? There is not one place that explains timers and automation. It's all trial and error. And the thing is it used to work and shut off properly. I’d appreciate your insight and help
What is the power output bi-led projectors with d3s led bulb vs bi xenon (on a4 b8 factory projectors). I am jnterested in lm/lux and difference in rain and fog. To know if should o just upgrade to new xenon projectors and night braker laser or to go with bi-led projectors and d3s led bulb.
Hola soy de mexico no entiendo mucho ingles pero esta muy bien el video crees que esto funcione para instalar unos faros de un suzuki swift sport 2015 a un suzuki swift glx 2014 ya que el glsx trae H4 y los faros del sport traen xenon hid muchas gracias apreciaria mucho tu ayuda
@area777th if the part has a top coat it will not work as fast. It can still strip the chrome but will take hours, possibly days, and the cleaner can start to break down some plastics after a long time of exposure.
Can i get the turn signal wire from the mirror turn light and courtesy wire from the puddle light wire if i want to run courtesy door handle light and also door handles right and left turn signal function as well.?
@@Sibhiya_christopher you can not have 2 controllers connected to the same leds. You would have to disconnect one and connect the other to use 2 controllers.
I tried for hours with my Hyundai Getz harness and only managed to burn the headlight fuse a few times. Can't figure out how it works. I tried from one positive to another (when you power the high beams you would also power the low beams, doing a jumper with the diode between both but didn't work) tried the way in this video and also didn't work. I ran out of ideas :(
@@NextLevelNeo it's a normal H4 with the square type plug. With a multimeter I checked the pins and I got constant 12v on the side parallel ones and negative on the top centre pin. When you turn the switch on to low beam only one side has 12v and the top is still negative but if you flick the high beams the negative top dies, the left positive dies and the right pin now is the one with 12v but the other two pins are dead (in another words, unless I earth it directly to the car I can't get the high beams to close the circuit...) Weird :(
my experience that has used several brands available in the market, I confidently state that your product is an improvement from other brand products. Long story short, your product is perfect and this is what we should all be using. thank you sir .
@tonywilless1723 once they have been customized the install is different. The only people that can help are the ones that made them. Im sure their build is a bit different than the way we build them.
@@NextLevelNeo I get your point thanks for the info if you could send a link for the installing them to the car video so I can get a basis to go off of they don’t have an install video or guide yet
@tonywilless1723 did you reach out to rgb halo kits to ask for an install tutorial? I'm surprised they don't have atleast a generic tutorial for their lights. Here is ours but once again these are custom and there is no standard way to build lights so they will vary one brand to the next. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-xNYSLBrnJLI.html
I'm sorry for all questions it's my first build but I have the same deep cool aio but a 4090 strix how much room do you have with the gpu vertical mounted and lower fans straight or on angle?
I have a 2020 charger with blue ghost I like to keep my drls 2 different colors any way in the app to keep them on when car isn’t running I have the drls on a switch
Hey would you happen to know if these were aftermarket headlights? The plastic housing in mine were an ugly beige when I stripped them, making it so I had to paint them black which turned out pretty bad lol.
