Micro SD cards read and write way too slow for this type of applications. (100MB/s vs 3-7GB/s) As to why they didn't have that option. But i think they should have a swapable/ empty m.2 slot honestly.
Thanks for the post but you're mixing input power (Voltage x Current = Watts) with audio output power. Most amplifiers have 2 ratings that are very aspirational. "Continuous" power, which is the highest volume an amplifier can provide at a constant volume and "Instantaneous" power, which is more of a peak reading. Both of these are wildly exaggerated by most companies for comparison with other companie's specs. They are a lot like gas mileage estimates, which you'll never see in real life driving. Audio power is also very dependent on the speaker and it's impedance and power rating so there are a lot of variables in the total Watts an amplifier can actually provide. For comparison purposes, this is a standard 100W amp that you can stack up against other gear you might be considering in that category. I hope that helps.
Yes, you can use the hub to charge any number of batteries including a single one or all three. Try swapping positions of the batteries to see if the charging issue changes. If it stays on the same slot, you have a defective hub. If it follows the battery, you might have damaged or dirty pins on the end of that battery. Good luck!
How about making a video on changing the internal gaskets or O-rings when it starts leaking below the yellow rubber ring that you turn for spray selection.
Sorry but I have had every single DJI drone out that wasn’t on the professional/commercial side. I have spent days with different cables, blocks, built in usb wall chargers and more. This hub is their worst. I could have a battery with 1-2 bars and not even get to 3 and charge for 2 days. This hub is terrible.
I have a mavic 3 battery. It's terminals got wet with salt water. I dried it off, and tried to fly with it. It was blinking a few lights, and it kept saying "battery communication error". So finally I went back to my hotel. Now it's totally dead, and no lights blink when I push the button. I put it in the drone, and it started the drone up, spun props and made DJI sound, but then nothing. I put it in my hub charger, and nothing happened. I emailed DJI support two days ago, but they haven't replied. Do you think this battery is finished, or can it be revived? It seems like it was a minor problem. Three other batteries got wet a little, but they still work fine. Thanks, Steve
It's better to understand how it works and that's why I did the review. For me to show it in action I would have had to have mice in my basement and shown them running away - impossible to demonstrate.
Thanks for the video. Very helpful. Question: It sounds like the only way to view the videos (without subscription) is to remove the USB drive and plug it into your computer. Can you view the videos that are on the USB drive from the phone app without removing the USB drive? Thanks!
So can we not view the videos from the app if it's on local storage? Do we have to pull the USB and plug it into a computer to view the videos? My free trial just ended and I'm not sure if it has switched over to local storage or not?? I haven't received any motion recordings for two days now.. and I'm not sure if that just means it's not recording them.. or I just can't see them from the app???
I've had good luck with them and use a pair of them in my basement and haven't seen a single mouse in 2 winters. You have to make sure you have enough of them to cover the area you're trying to protect.
Hello! I just wanted to thank you for the information! I’ve been looking for a video that helps me understand if I could take my DJI Air 3 and lithium ion batteries on a plane and couldn’t find any but you! I now know that it holds 62.6 Wh thanks to you! I’ll be taking everything in my trip to Hawaii in a few weeks! Thank you so much!!
Yes, you can use a 67W charger and it'll work fine. The Battery Hub controls the charge and as long as the charger can supply 65W or higher you can quick-charge your batteries safely. Thanks for the post!
Can you tell me why local storage is not working? It was working for years and then it stopped. Call Blink and they looked at it and couldn't determine the problem. Could it be the router? Help> .
I had a similar issue and using a different USB Thumb Drive solved the problem for me. You might want to try formatting the one you're using in your computer before inserting it into the hub.
I looked at several of videos talking about this light. You gave the best demonstration for somebody that knew using this type of product in the explained it very well very nice work. I recommend your videos to anybody. I am a musician and I really like how you offered the knowledge to operate these lights and you input the manual several times, great work
Hello, and congratulations for the video. Just one question if you have eight rooms do you have to put them all in DMX with the cable or once they are synchronized you can remove the cables ?
What I really need to know is what is behind the plastic nozzles. I would have like to have seen you remove that so that we could see behind to see if there is more plastic.
You need to play your music loudly with Pyle amps, in order to drown out their noisy cooling fans, which are identical in all of their models. If the company upgraded the crappy fan, their feature-rich products at such low prices would be a great. Those without a fan, of course, do not suffer the problem.
Exactly the information I was looking for and right to the point. Moreover I didn’t have to fast forward over anything or set your talk speed to 1.25. 💪🏻
What’s the best way to access the camera when it’s in the housing (2nd option) to change the batteries whilst it’s attached to a external wall Literally gotta set it up via a ladder or leaning out a window 🤷🏻♂️
AWFUL APP MALFUNCTIONS!!!! I just bought a JLAB JBUDS MINI over a month ago and sent it back to the dealer at my own expense for testing due to malfunctions. They claimed that they tested it for 5 hours over two to three days with different phones and found no issues. (P.S. I had tested it myself for a month after purchasing, experiencing problems with connectivity to iPhones and various Bluetooth transmitters on different computers. Often, while riding my bike, the sound would cut out midway.) Upon receiving it back, I reset it immediately. I decided not to modify any of the customized touch controls. However, when I connected it to my computer and listened for nearly half an hour, the issues persisted. The factory default setting triggers the music/movie mode when the left earbud is long-pressed. When I pick up the earbuds to put them in my ears and adjust the fit, this mode often triggers. After about 3 minutes, the sound suddenly cuts out in the right ear. Then, by long-pressing the left ear, I can bring the sound back. After around 3 minutes again, the left ear loses sound, and no amount of pressing or tapping can restore it. The touch controls still respond, but there is no sound (so it's not a wiring issue, just silent). So, I believe it's a flaw in the factory's built-in functionality. The dealer probably didn't test the app functionality. But if at the same price of $NTD1280, without needing the app or customized touch controls, I could have chosen the entry-level EARFUN $NTD1000 (I bought the first generation last year, and its sound quality is even better than this one). I'm currently doing a second reset because the frequent accidental triggering in the left ear is annoying. I've directly set the long-press on both ears to adjust volume. Let's see if this resolves the issue and if I can replicate the dealer's 5-hour test without any problems. This is a disappointing experience with this brand earphone.
